Table of Contents
The majority of sump pumps will have a built-in fitting for a specific sized discharge pipe that is usually 1.25”or 1.5” interior diameter. With a properly sized discharge pipe will ensure that your sump pump will work efficiently for a long time.
What size is sump pump discharge pipe?
Most sump pumps have a built-in fitting for a certain sized discharge pipe, typically 1.25” or 1.5” inside diameter.
What pipes go into sump pump?
The sump pump typically uses a 1½” PVC pipe discharge the water from the basement. You should see this pipe going through the foundation wall to the outside of the house. What else is in the sump pump pit? In older homes sump pumps may be connected to the sanitary sewer system.
How far should sump pump drain from house?
It is important to keep the discharge point of your sump pump as far from your foundation as possible. The minimum distance should be 10 feet. Most discharge pipes have a flexible hose tightly attached to the pipe coming from the basement.
Can a sump pump be too strong?
If the pump is too small, it won’t be able to keep up with water flowing into the basin. If the pump is too powerful, it will “short cycle.” This means the pump will start and stop frequently, which can cause premature pump failure.
Why are there two pipes in my sump pump?
So there are two pipes coming from an ejector pit – there’s the drain pipe and there’s the vent pipe. A sump pump should have a battery backup system so that it can continue to work in case of a power outage.
Why does sump pump run when it’s not raining?
Increase in Ground Water The most common reason for your sump pumps keeps running while it is not raining is an increase in groundwater. This water is almost impossible to detect above ground but it can pool at the lowest point in your home causing the pump to run nonstop.
Can I run my sump pump into my sewer line?
While it may not be illegal in your area, connecting your sump pump to the sanitary sewer is in fact illegal in much of the U.S.—and for good reason. During big storms or heavy rainfall, the sewage treatment plants can become overloaded. Nothing, if you’re not connected to the sewer line.
How deep should a sump pump line be?
In most areas this means the lines should be buried 2 to 3 feet underground in most parts of the United States. If the pipes are not deep enough they may freeze during heavy snowstorms.
Can you bury sump pump discharge line?
The line can get buried by mulch, dirt, or grass. This happens whether it is buried or not, but it is a good practice to check the end of the discharge every time you mow your lawn to ensure this doesn’t happen. The line can freeze or get buried by snow, causing it to block the water flow.
Where should the sump pump discharge route be?
Plan your garden near the bottom of a natural slope in your lawn, at least 10 feet from your foundation and downhill from your sump pump. To find the best spot, dig a hole 12 inches deep and fill with water. If the water is gone in 24 hours, then it’s the perfect place for a rain garden.
How far can you run a sump pump line?
For most average-sized homes in areas with average water tables, a 1/3 HP sump pump should be sufficient. Typically, 1/3 HP pumps can handle 7′ – 10′ vertical lifts from the sump pit if they have one 90-degree elbow and a horizontal pipe run between 3 feet and 25 feet.
What’s better 1/3 hp or 1/2 HP sump pump?
When used in similar conditions, a 1/2 horsepower pump will pump more water and lift it higher than a 1/3 horsepower pump. The 1/2 hp pump shouldn’t cause any problems, but in situations where the water flow into the sump is relatively slow, you would have no advantage by using the larger pump.
How far can a 1/2 HP sump pump push water?
If water is higher than usual, a 1/3 HP can handle a higher vertical lift when discharging water. A 1/2 HP sump pump can handle 7 to 10 feet vertical lift off the sump pump, a 90-degree elbow and a horizontal pipe running between 3 and 25 feet.
How far can a 1 HP sump pump push water?
A 1 HP sump pump has significant vertical and horizontal reach, making it ideal not only for residential homes but also for commercial units. These pumps deliver an average of 19 GPH and can lift water from wells that are 200 feet deep.
What PVC pipe is used for sump pump?
Recommended Tools for Installing a Sump Pump 1.5” Schedule 40 PVC pipe (10 ft.).
Should sump pump sit on bricks?
Ensure your sump pump doesn’t sit on debris such as silt or gravel, which could be sucked up into the pump, ruining the motor. Instead, place it on steady, flat bricks. Also, ensure the sump basin has a filter fabric around it to stop debris from coming in.
Do you need a weep hole in sump pump?
Sump pumps need Weep Holes (relief holes) in order to prevent air locking the impeller chamber. This is important because it allows air to bleed out of the interior of the pump that would normally keep the next cycles from starting.
