Table of Contents
Kitchen sink P-Traps come in 1-1/2” standard size, while bathroom sinks use P-Traps of 1-1/4” standard size. The traps also come in different material types such as propylene, ABS, brass (chrome-plated or natural), and PVC.
How do I know what size P-trap to get?
If you have 2.5 inches from the bottom of the tailpiece to shelf and 0.5 inches from the drain to shelf you can use CP-trap. First you have to cut 2.5-2.0 inches from the end of the tailpiece. The height of the p-trap is 4.5 inches 5-2.5=2.5 inches or 4.5-2.5=2.0 inches.
What size P-trap is typically needed when replacing a bathroom sink?
Traps come in 1-1/4 inch (standard bathroom sink) or 1-1/2 inch (standard kitchen sink) inside diameter sizes. Be sure to check so you get the right size replacement at your local store. In this guide we’ll show you how to replace a P-trap in a few easy steps.
Can I use 1 1/2 inch P-trap for bathroom sink?
All sizes are I.D. (internal diameter). All are Schedule 40. Part 2. Yes, 1 1/4″ is still used for bathroom sinks and vanities, typically in a 1 1/2″ x 1 1/4″ reducing p-trap or in a 1 1/2″ x 1 1/4″ reducing trap adapter.
What size pipe is used for bathroom sink?
The standard size for a bathroom sink drain pipe is 1.25 inches in diameter. However, this is determined based on your state’s housing code, and you may find that they suggest 1.5 inches or 1.65 inches in diameter, and your home has been built with this plumbing standard.
What size are bathroom P traps?
Choosing the Right P-Trap Kitchen sink P-Traps come in 1-1/2” standard size, while bathroom sinks use P-Traps of 1-1/4” standard size. The traps also come in different material types such as propylene, ABS, brass (chrome-plated or natural), and PVC.
What size are sink traps?
Generally, the following types of appliances use a standard size waste trap and waste pipework: Wash hand basins: 32mm (1 ¼ inch). Sinks: 38mm (1 ½ inch). Urinals: 38mm (1 ½ inch), or 50mm (2 inch).
What can I use instead of AP trap?
Alternative 1: HepvO Waterless Valve. Alternative 2: Bottle Trap. Alternative 3: Grease Trap.
Does a bathroom sink need a trap?
Beneath a kitchen or bathroom sink drain is a pipe with a sharp bend in it. You must have a p-trap installed under your sink if you want your home to pass inspection in many places, where the building code requires them. Even if they are not required, you should understand the practical purpose for installing a p-trap.
What size are sink drains?
Kitchen drains and drain lines are sized for functionality. All kitchen sinks today have the same diameter drain, which is 3 1/2 inches and is larger than a bathroom drain which measures in at 1 1/4 inches. It is the same size as a typical standard shower drain, however.
How do you measure a bathroom sink trap?
Measure from the wall where the house drain pipe is to the nut securing the J trap to the sink drain pipe with a tape measure. Add two inches to the measurement and write it down on a piece of paper. This is the measurement for the rear sink drain pipe.
What is the height of a 2 inch P-trap?
The trap is usually attached to the end of the tailpiece, and tailpieces are typically between 6 – 8 inches long (though I’ve seen up to 12). So the “standard” height of a trap would be, 6 – 8″ below the fixture.
How deep is a sink trap?
The trap seal depth in the P trap should be a minimum of two inches deep and a maximum of four inches – see the diagram below to know how to measure it.
How much room do you need for P-trap?
Maximum Distance According to the International Residential Code, the maximum vertical distance between the sink drain and the entrance to the p-trap is 24 inches.
What trap do I need for my sink?
This water creates an air seal which helps stop smells making their way from the drain back into your house. Bathroom wash hand basin wastes use a 32mm / 1-1/4 inch trap. Kitchen sinks, baths and shower wastes use a 40mm / 1-1/2 inch trap.
Are bottle traps standard size?
Standard bottle trap. 1.1/4″/32mm with 3″/75mm seal.
Which is better P trap or bottle trap?
Like the ‘P’ trap, a disadvantage of the ‘S’ trap is that it requires a fair amount of room around the waste outlet. The ‘Bottle’ trap takes up less radial space under a waste outlet and is ideal for pedestal mounted basins where space is usually very limited. They can however be deeper that the ‘P’ and ‘S’ traps.
Can you replace metal P trap with PVC?
Purchase a PVC P-trap, pipe and fittings to replace the metal ones. PVC drain pipe comes in two different diameters: 1 1/4 inches and 1 1/2 inches. Make sure to buy material that’s the same diameter as the metal pipes you just removed.
Does P trap have to be below drain?
It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times. But essentially anything below already creates its own p-trap- so using another is redundant.
Why does my P trap smell?
A p trap is designed to use water to block the sewer gases from leaking up the drain. If a sink’s p trap dies out this can result in a drain that smells bad. To alleviate this problem pour water down the drain to restore the water barrier in the p trap.
What is the name of the fitting that connects the P-trap to the drain?
The drain is connected to your P-trap and plumbing connection hidden within the walls. Tailpiece: Often referred to as the drain tailpiece, this is the section of piping that connects to the drain fitting. It carries water away from the sink.
