Table of Contents
What size should fascia board be?
Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
What size fascia do I need?
Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick – our most common range is the 18mm Replacement Fascia.
Can you use 2×4 for fascia?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt. See detail below.
Is fascia a 1×6?
Fascia Board Sizes #1 – 1×6 This is the most common fascia board you will find. Usually you have a 2×4 sub fascia behind this fascia board. Standard gutter size for residential homes is five or six inches. At the backside of a 5 inch gutter, the fascia board mounting area will be four inches tall.
How do you measure a fascia board?
Measuring and Cutting the Fascia. Use a tape measure to find the length of your roof. Climb a ladder near the corner of your roof and tape the end of your tape measure against the rafter using duct tape. Get off of your ladder and reposition it at the other end of your roof.
What board do you use for fascia?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
Should I use pressure treated wood for fascia?
It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.
How do I choose a fascia?
You should choose colors that will complement your siding and your home’s overall look. Therefore, if you have navy blue siding, bright white soffit may not be the best choice. Some manufacturers create soffit and fascia in other colors, but you will have to paint the materials if you want unique colors.
Do you install fascia before roof sheathing?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. Add an inch and a half for subfascia, strike a line. Add the thickness of the true fascia, 15/16 in., in this case.
Can you use plywood for fascia?
Even though plywood siding isn’t a good fascia material, it works well for soffits, which are out of the rain and have to be painted and cut to install light fixtures and vents.
How do you attach fascia to roof trusses?
Instructions for How to Attach Fascia Board to Roof Trusses Mark the place closest to the end of the board that aligns with the center of a joist. Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place.
What are the dimensions of a 1×6 board?
A 1×6, for example, actually measures 3/4″ x 5 1/2″. In this case, the planing is necessary for a smoother surface, so that the board could be used for interior applications. The length of the boards is generally exactly what you order, though we usually only stock pieces of even lengths.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
Can you use cedar for fascia board?
Commonly referred to as a durable species, cedar is a very popular choice for construction, siding, and, yes, fascia boards. This makes cedar quite an ideal material in terms of retaining its shape while at the same time taking to staining and nailing well.
How do you calculate soffit and fascia?
Multiply the total length by the width to obtain the area of soffit needed to fill the gap. For example, if the total eaves length is 110 feet, and the width is 2 feet, multiply 110 by 2. The result, 220 in this example, is the number of square feet of soffit required.
Can you use treated lumber for fascia board?
Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.
What type of wood is used for eaves?
All About Eave Eaves are simple boxes. The bottom — or soffit — where the damage is, is typically thin plywood, usually 1/4-to-3/8-inch-thick. It’s cut in long sections and butt-jointed together with a thin piece of plastic molding that slips over both ends forming a joint.
