Table of Contents
Does an 18 inch bar take an 18 inch chain?
General chain lengths, like 18 inches, are not interchangeable. That’s because chainsaw chains actually have three measurements: number of drive links, pitch, and gauge.
How do I know what size chain I need for my chainsaw?
To get the correct size, simply count 3 rivets on the chain and measure the distance between them from the centre points. Now divide this by half to get your size. As an example, three rivets that measure ½ an inch across divided by two gives you a pitch of a ¼ inch.
How many drive links in a 18 inch chainsaw?
0.050 Gauge 0.325 in. Pitch Chainsaw Chain, 72 Drive Links. Designed for professional woodcutters using .
Can I put an 18 inch bar on a 20 inch chainsaw?
A chain saw engine turns a sprocket. Changing the bar and chain on your 18-inch chain saw to a 20-inch size will enable easier cutting of larger trees and branches. Larger chain saws cut through thicker trees and limbs. Put work gloves on to protect your hands and fingers.
Can I put an 18 inch bar on a 16 inch chainsaw?
Yes, but you need a bar designed to fit on your saw. There are different designs for different saws, and the bar has to match the chain/sprocket configuration as well.
How do I know my chain size?
To determine the pitch (chain size), you’ll need to measure the distance between any three consecutive rivets, then divide the result by 2. The rivets are the small, round pegs/studs that hold the chain segments together. Measure from the first to the third, then divide that number in half to get your chain pitch.
What does 72 mean on a chainsaw chain?
72 = 3/8 pitch .050 gauge or 1.3mm. 73 = 3/8 pitch .058 gauge or 1.5mm.
Does the number of links in a chainsaw chain matter?
Number of links is to fit the bar – pitch is to fit the sprocket. Since the number of links is larger(81 instead of 74), there is low chance that it would fit properly.
What is the difference between .325 and 3/8 chain?
325 is a smaller top cutter and tie strap it is easier to turn for a saw . The 3/8 is a bigger top cutter and tie strap . Mainly in a 20 ” chain has more cutters in .
What is the difference between S62 and y62 chainsaw chains?
Looking at both specs they both use a 5/32″ file and . 050 groove width fin and on the Home Depot y62 chain info it says it replaces the S62 Oregon chain. The S62 is one chain in package and S62T is two chains in package.
Can you put any bar and chain on a chainsaw?
More specifically, chainsaw bars vary both in mount geometry as well as in intended chain pitch and gauge, which must match those of your saw and chain. Because of this, you cannot just fit any bar on any saw.
Can you put a different size bar on a chainsaw?
Most chainsaws can operate up to three different bar sizes. Guide bars are measured in length, from the tip of the bar to the heel, and range in size from 14 to over 40 inches. Check the specifications in your model’s operator’s manual to see what size bars you can run on your saw.
What size bars does Stihl make?
STIHL guide bars range from 10″ (found on our tree-trimming pole pruners) to an incredible 59″ (used in extreme felling operations).
What size chain is on a Stihl ms180?
Quick Chain Adjuster (QCA) (B) POWER SOURCE Gas GUIDE BAR LENGTH (Recommended) 16 in. OILOMATIC® CHAIN 3/8″ PMM3 CHAIN OIL CAPACITY 4.9 oz. ENGINE POWER 2.0 bhp.
Do chainsaw bars wear out?
As a chainsaw bar wears out, you’ll lose cutting accuracy and efficiency. You shouldn’t notice a whole lot of back-and-forth, but a worn chainsaw bar will allow a lot more movement side to side. There’s a reason for this. Your chain fits into your bar tongue-and-groove style.
Can you put a 18 inch bar on a 14 inch chainsaw?
Different Bar Sizes A Poulan 14 chainsaw can operate with a bar that’s 12, 14, 16 and 18 inches length. However, a larger bar may not always give the best cutting performance.
What’s the difference between 404 and 3/8 chain?
Secondly, the numbers 3/8″ and . 404″ refer to the pitch (distance) between the drive links – these are the bits on the chain that stick down and engage with the drive sprocket on the saw, and the sprocket on the roller-nose end of the bar.
What chainsaw chain cuts the fastest?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).
What do Stihl chain numbers mean?
Find the gauge of the chain by locating the number stamped on the drive link. A 1 equals a 0.043-inch gauge, 3 equals a 0.050-inch gauge, 5 corresponds to a 0.058-inch gauge, 6 means the chain has a 0.063-inch gauge. A 0 means the chain has a 0.080-inch gauge, but this gauge size is found only on the Harvester chain.
