Table of Contents
A jigsaw is a real all-rounder when it comes to cutting laminate floors. It’s best used to cut out shapes from your board. For example, when you want to place boards around your toilet or maybe a pillar. Always use a fine toothed blade and have the saw blade spinning before you touch the board.
What type of saw is best for cutting laminate flooring?
A circular saw is an electric saw that spins quickly and makes straight cuts. It is one of the best tools to use when shaping laminate and can be held in one hand, although a stand should be used to hold materials in place.
Is a miter saw good for cutting laminate flooring?
The easiest saw to use for cutting your planks to length is a power miter saw, or chop saw. These saws are available with 8- to 12-inch diameter circular blades. You can cut the material in one motion, and the fence aligns the material to the blade for a perfect cut every time.
How can I cut laminate without chipping?
To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.
How many tooth saw blade for laminate flooring?
In view of this, a thin kerf, 80 to 100 tooth, carbide-tipped blade is most effective for cutting laminates and will last for about 1000 sqft before needing to be re-sharpened.
Can you use a miter saw for flooring?
A miter saw can be used on the floor, but it may be challenging to hold the board you are cutting level and in place. You can always buy or build a miter saw stand so you won’t have a hard time to work with your miter saw on the floor.
What size Mitre saw for laminate?
Smaller saws that are 254mm (10 inches) or smaller are easier to handle and are better used for smaller, more detailed cutting work. The size of saw you use here depends on the size of the laminate flooring. For larger laminate floors, a 305mm saw could be ideal, whereas smaller areas could benefit from a smaller saw.
What can I use to cut laminate?
In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter. However, using a diamond blade is recommended as laminate can be tough to cut through and may damage another type of blade. Typically, you will cut with the finished side up.
How do you cut Formica without chipping it?
You can minimize the potential for chipping if you use a finish blade with lots of teeth, making sure the sharp is keen. You can further reduce the chance of chipping by using masking tape along the cut line and cutting through the tape. As with all cutting, measure at least twice and mark the line well and clearly.
What is the best way to cut laminated chipboard?
Using a jig saw will give you a potential spoil on both edges due to the reciprocating action. A circular saw is better and you can minimise the chipping by putting masking tape along the cut lines. Another way is to undercut and bring down with a power planer.
Does laminate flooring dull saw blades?
You see, laminate flooring will destroy a wood cutting blade with alternating top bevel (ATB) teeth in no time at all. The sharp points on this type of blade can’t handle anything that hard – they dull quickly and those tips are what the blade uses to cut cleanly through wood.
Can I cut vinyl flooring with a miter saw?
A miter saw is a great tool for cutting vinyl flooring. You can slice the pieces of flooring quite easily. It gives a clean and flawless finish due to straight edges, unlike some other saws. Using a miter saw is simple – you just need to make accurate cut marks.
How many teeth do I need to cut laminate?
Diamond-tipped blades that are made for laminate and fiber cement usually have a low number of teeth to reduce the dust produced by cutting cement. However, typical circular and miter saw blades that are used for laminate will have 80 to 100 teeth for fine, precision cutting.
How big of a board will a 12-inch miter saw cut?
Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
What can a 12-inch miter saw cut?
Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights. This larger saw can cut a maximum thickness of 3 1/2 inches, enough to cut through four-by-fours.
What size Mitre saw for trim work?
Size. A 10-inch miter saw—so-called because it has a 10-inch blade—is sufficient for cutting most types of trim boards and siding strips, which are typically less than 3/4-inches thick and 6-inches wide.
Can you cut laminate with a utility knife?
A utility knife can be used to make scoring cuts on Formica. Since all plastic laminates are essentially the same, cutting Formica with a utility knife is identical to cutting most laminates. This method works well for one or two shorter cuts, but is too time consuming and inconsistent to use for larger projects.
Can you use a utility knife to cut laminate flooring?
A regular utility knife blade can be used to cut flexible, self-adhering laminate strip material. The caveat is that you must change the blades frequently so the knife cuts properly — a dull blade will not cut effectively.
