Table of Contents
Depending on where you live and the part of your home you’re insulating (walls, crawlspace, attic, etc.), you’ll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.
Is R30 good for ceilings?
At a minimum, use R-30 insulation in the ceiling of your home. The thickness of the insulation depends on the material and insulation type. One thing is certain, your energy bills will be lower with an insulated ceiling. For ceilings, R-30 insulation is the recommended minimum.
What type of insulation is best for ceilings?
Insulation Batts Batt insulation is a type of insulation blanket. These are pre-cut sections of insulation that are usually fiberglass, although cellulose, mineral wool, natural fibers and plastic versions are also available. Best for unfinished walls, floors and ceilings.
How much insulation do I need in my ceiling?
R-Value is a measure of insulation’s ability to resist heat flow. The higher the R-Value, the better the thermal performance of the insulation. The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
What is r12 insulation used for?
Description. This Johns Manville insulation was created for walls and attics to improve energy and acoustic efficiency. You will appreciate the flexible material made of fibreglass without formaldehyde and resistant to fire and mildew.
Can you use R19 in ceiling?
Vapor barrier installed below the bottom cords on the strapping for the drywall completes a great ceiling design. If you are adding R19 to current insulation then yes, you can add the batts of insulation cross ways over the existing layer and above the joists or bottom of the trusses.
Is R30 thicker than R19?
The bigger the R value, the better the insulation is at slowing down the heat transfer. So R19 is better insulation than R13, and R30 is better than R19. The larger the R value, the better the insulation value.
Why is a higher R-value needed in the ceilings?
R-Value is a measure of insulation’s ability to resist heat traveling through it. The higher the R-Value the better the thermal performance of the insulation.
What insulation has the highest R-value per inch?
Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.
What type of insulation has the lowest R-value per inch?
The higher the R-value, the better it insulates per inch of thickness.Comparative Insulation R-Values. Insulation Type: R-Value per Inch: Fiberglass (loose) 2.2 – 2.9 Fiberglass (batts) 2.9 – 3.8 Cellulose (loose) 3.1 – 3.8.
What is the R-value of 18 inches of insulation?
Warm Climates (R-30 to R-49): Fiberglass (blown): 14” – 18” Fiberglass (batts): 11” – 14”.
What is R30 insulation used for?
R30 insulation is the minimum insulation recommended for an Attic from climate zone 1 to 3, while it can be used in cathedral ceilings in all climate zones across the USA. It can be used as maximum insulation in climate zones 4 – 8 of the USA for floors.
Is higher R-value better?
“R” means resistance to heat flow. Here’s what to know: The higher the R-value, the greater the insulating power. Almost all insulation products have to tell you their R-value — including duct wrap.
Is R 3 good insulation?
The higher the R-value, the more effective the insulation. 2 to R3. 7 per inch of thickness. With every inch of blown-in cellulose you install, you get that much more in R-value.
What is the R-value of 10 inches of insulation?
R-value of Materials and Depths Material R-value/in 10″ Fiberglass (batt) 3.1 – 3.4 31.0 – 34.0 Fiberglass blown (attic) 2.2 – 4.3 22.0 – 43.0 Fiberglass blown (wall) 3.7 – 4.3 37.0 – 43.0.
What is the R-value of 2 inch Styrofoam?
A wall utilizing STYROFOAM T-MASS Technology with a 2-inch exterior layer and a 4-inch interior layer of concrete along with a 2-inch layer of STYROFOAM extruded polystyrene insulation would result in a material R-value of approximately 11.33.
Is R19 enough for attic?
Most homes only have R19 in attics. To give you an idea that’s only 5 1/2 inches of insulation. That’s ok for your walls. So by adding another R19 “5 1/2 inches will give you an R38 value.
What is the thickness of R19 insulation?
The standard R-19 fiberglass batt is 6.25″ thick. If you put that batt in a closed 2×6 wall, it will be compressed 0.75″ because a 2×6 is 5.5″ deep. That means the batt labeled R-19 really gives you R-18 in a closed cavity.
How thick is R19 blown insulation?
6.75” R-Value Thickness Bags / 1000 Sq Ft R44 14.75” 20.1 R38 12.75” 16.8 R30 10.25” 13.0 R19 6.75” 8.1.
What does R 11 insulation mean?
R-value refers to resistance of heat transfer. Air is a very poor heat conductor. Materials trapping and isolating air in cells limit the heat transfer. The greater the limitation, the greater the R value, so R-11 has lower insulative properties than R-15.
Is R 21 insulation good?
If a home is heated by a less-efficient system, such as electric baseboard, R-21 insulation is a better value. Since the house will retain more heat in the winter months, the electric heat can be used less often, saving money an quickly recouping the initial investment on the more expensive insulation.
Is r38 insulation good?
In many colder areas of the US, R 18 is the recommended insulation for walls (its a 2×6 wall stuffed with standard fiberglass insulation), R 38 (14 inches of fiberglass) is recommended for ceilings/attics.
