Table of Contents
Attaching Quarter Round Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well.
Can I use 16 gauge nails for quarter round?
They work well on birdhouses and other thin cuts of wood. Brads are excellent for trim work, including narrow trim around windows or doors, shoe moulding and quarter-round moulding. Finish nails are versatile nails with a 15- or 16-gauge diameter. They’re designed for thicker cuts of wood.
What is quarter round nailed into?
Tip. Choose finish nails that are long enough to penetrate the thickness of the quarter round molding and the drywall with enough left over to go at least 1/2 inch into the wall’s base plate. Place the nails no more than 18 inches apart for 3/4-inch molding.
What size brad nails do I use for quarter round?
Use 1 1/4 inch nails for quarter round (with typical 3/4 inch thickness), shoe molding, trim molding over laminate floors, and plywood flooring. Use a size less than 2 inches for paneling, typically 1 inch to 1 5/8 inches. Use shorter nails for board and batten. Less than 1 1/5 inches is ideal.
Can you use 18 gauge nails for quarter round?
If you’re doing lighter molding, such as quarter-round at the bottom of your wall, or installing a chair rail, an 18 Gauge Brad Nailer is fine for the job.
Can you use a brad nailer for quarter round?
The preferred tool for nailing shoe molding or quarter-round is an electric finish or brad nailer. This tool will automatically set or recess small finish nails, and can greatly speed up your work. To use a nailer, first calibrate the depth of the nailer, using a piece of waste trim on another waste board.
Can you hand nail quarter round?
Quarter-round covers small gaps between the baseboard molding and the floor and offers some aesthetic appeal. When replacing quarter-round, many contractors use a nail gun and compressor. However, most homeowners only require simple hand tools to nail quarter-round baseboard trim.
Should I nail or glue quarter round?
A: Quarter-round should be nailed to the base boards only. It is intended to hide gaps between the base and floor. It should also permit a little movement in the flooring. Plus, it absorbs the impact of feet and furniture legs, so you may want to replace it sometime—thus, don’t glue it.
What nails do you use for molding?
The most common size used in moulding is 1-1/4″ (3d) or 1-1/2″ (4d) finishing nail. Select a galvanized or stainless steel nail for outdoor use. Nail Set: use to drive the nail below the wood surface without marring the moulding. Hammer: allows you to drive a nail into a piece of moulding.
Which is bigger 15 gauge or 18 gauge?
The difference between them is the gauge nail that they shoot. The most common and readily available types are 15 gauge, 16 gauge, 18 gauge, and 23 gauge. The higher the number, the thinner the nail and the smaller the hole.
What is the difference between a brad nailer and a pin nailer?
For starters, brad nailers use a much larger 18 gauge nail. This nail has a much larger diameter head, which is why a brad nailer leaves a visible nail hold that must be covered with putty. Pin nailers, on the other hand, use a smaller 23 gauge nail.
What size quarter round should I use?
Consideration #1: The scale of your house–The most typical dimensions of quarter round are ¾” x ¾” while the most common size of shoe molding is ½” x ¾”. Suppose you lived in a gigantic palace and your hallways could accommodate your car driving through them with room to spare.
What size brad nails should I use?
The rule is simple: a brad should be three times as long as the thickness of the material you are fixing. Example: if the material is 15 mm thick, the brad should be 45 mm long. Choose a brad gun that takes the length of brad you need.
What size nails does a brad nailer use?
Brad nailers use smaller 18-gauge nails. Brad nails (often just called brads), are 18 gauge, which is 0.0475 of an inch. They vary in length from ½ to 2½ inches. By comparison, a 16-gauge finish nail is 0.0625-inch thick.
Is shoe molding the same as quarter round?
Quarter round is another moulding style typically paired with baseboards to cover up gaps and imperfections between the base and the floor. As such, it essentially has the same purpose as shoe moulding. However, this style of moulding is always shaped like a quarter of a circle, hence the name.
Can a finish nailer use brad nails?
Brad nails are formed from a fine, 18-gauge wire, which means they are smaller in diameter and typically have less holding strength. The benefit to an 18-gauge brad is its size. Finish nailers will run 15- or 16-gauge finish nails, in both angled and straight varieties depending on the tool.
Should quarter round be nailed to floor or baseboard?
Be sure you hold the quarter round tight against both the baseboard and floor for a tight fit. To hand-nail molding, drive each nail almost flush with the quarter round, then use the nail set to sink the head beneath the surface. Use putty to cover the nail holes.
