Table of Contents
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
How long should my arrows be for a 28.5 draw?
A good rule of thumb is to cut it no shorter than the middle of the riser. At full draw, your arrow end would sit right in the middle of the shelf.
How long should my arrows be based on draw length?
it depends on the arrows you choose, you need at least 1/4″ of arrow overhang on the rest. so you can probably shoot an arrow that’s about 28 1/4 for rests that are set up normally. and go all the way up to full length 36″ arrows for indoor. i would suggest 1″ of overhang on your rest.
How long should my arrows be for 27 inch draw?
The arrow must be 29″ in length and supported by two points, which are 28″ apart. The number of inches the arrow deflects or bends due to the weight, is the spine size or measurement of an arrow. DYNAMIC spine describes the way an arrow reacts from the stored energy of a bow as it is shot.
How long should arrows be for 29 Draw?
How to: Select the perfect arrow Bow Arrow length Draw weight lb. 25″ 29″ 15-20 700 600 20-25 700 600 25-30 700 500.
How long should arrows be for 28 inch draw?
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
How long should my carbon arrows be?
The best safety practice is to make sure your arrows sit at least 1″ beyond your arrow rest when the bow is at full draw. A little bit of extra arrow length gives the arrows an important margin of safety. A little too long is okay. A little too short is not.
How long is a 340 arrow?
As you cut those arrows to fit your draw length, you make them stiffer. That’s why Gold Tip recommends the 400 spine for a 27-inch arrow shot at 60 pounds, as compared to the 340 at 30 inches. Understand that the manufacturers’ charts refer to arrow length, not draw length.
How do you measure arrow draw length?
When you reach the anchor that seems comfortable, have someone mark the arrow adjacent to the rest mounting hole in the handle riser. This mark should be directly above the grip where your hand touches the deepest part of the handle. The distance from this mark to the recess in the nock is your true draw length.
What happens if arrows are too long?
If, however, by being too long, the arrow’s dynamic spine is too low, then the arrows will not be accurate as they will tend to “fishtail” in flight. They will also tend to fly to the right (for a right handed archer).
Whats the shortest you can cut an arrow?
Arrows that are cut too short can be drawn past the arrow rest which could result in the arrow falling from the string, jamming, or otherwise causing damage to the arrow or the bow, and could even lead to personal injury. Never shoot an arrow that is less than one inch past the arrow rest at full draw.
Is draw length the same as arrow length?
Draw length – Put simply your draw length is how far you draw back the bow string to your anchor point. This is measured in inches so mine is a just under 28 inches 27 1/2 if you want to be exact. Arrow length – Your arrow length is how long your arrow is.
What is a 340 spine arrow?
Aluminum and carbon-fiber combination arrows are measured by spine deflection. A smaller number means that the arrow has a stiffer spine. For example, 3-60/340 means three wraps of carbon-fiber with an aluminum core tube diameter of 60 and a spine stiffness rating of 340.
What does 350 arrow mean?
The numbers refer to the spine of the arrow. The different spines refer to the stiffness, a 400 spine arrow is generally for bows 40-60 lbs. 350 spine is for bows roughly 55 – 75 lbs, and a 500 spine arrow is for bows roughly 30 – 50 lbs. That number is the stiffness of the arrow, referred to as the arrow spine.
Where should arrows be at full draw?
Arrows should be at least 1.5″ – 2″ beyond the back of the riser at full draw. Arrows should be at least 1.5″ – 2″ beyond the back of the riser at full draw.
How do you determine your draw length?
To measure your draw length, stand with your back to a wall stretching your arms out against the wall. Measure the distance from the end of your middle finger to the end of your other middle finger, basically the length of both arms, hands and chest. This measurement, minus 15 then divided by 2, is your draw length.
Can carbon arrows be cut to length?
Carbon arrows are a lightweight alternative to aluminum, but they may not always come in the correct length you need. While you can always take the arrows into a hunting store to have them cut by a professional, you can also cut arrows at home with a rotary cutter or an arrow saw.
Can you cut carbon arrows with a chop saw?
I think i will use that. If you use that cheapy chop saw as a chop saw, cutting the arrow by pulling the saw down to the arrow, you will never get any consistant cuts.they won’t cut perfectly square. It works much better to have a stationary, solid mounted motor and wheel and to spin an arrow into the cutting wheel.
Can you cut carbon arrows with a pipe cutter?
A pipe cutter won’t work to cut carbon arrows. They will splinter if you try it. A Dremel with a cut-off wheel will work, but you will need to square the end after.
How heavy of an arrow should I shoot?
Bentcik said few Americans use arrows weighing 700 grains or more unless they’re shooting traditional equipment. Archers who shoot a recurve or longbow normally use arrows weighing 700 grains or more.
