Table of Contents
What is Thinner 200 used for? Epoxy Primer Thinner 200 is used as a thinner for 2-part epoxies like TotalProtect, Aluminum Boat Barrier Coat, and 2-Part Epoxy Primer systems (surfacing, high-build, and clear). It is also used as a pre-paint surface prep solvent for inflatable boats, and to clean painting equipment.
What can I use to thin epoxy primer?
When using acetone or paint thinner for thinning epoxy, the general rule of thumb is a maximum of 10% added to the epoxy resin. An example would be if you had 32 ounces of epoxy that you were mixing you would only add up to 3.2 ounces of acetone to that mixture. Recommend over acetone and other solvents.
Does epoxy primer need thinner?
We do not recommend thinning epoxy with solvent at any time, and here’s why: Adding 5% lacquer thinner to epoxy reduces epoxy’s compressive strength by 35%. As such, it’s no longer suitable as a structural adhesive. Adding a solvent can extend curing time, making your work unpredictable.
What do you mix epoxy primer with?
Mix the desired quantity of Base & hardener (Mixing Ratio is 4: 1 Base to Hardener by volume). 4. After mixing these two components in proper ratio stir well & allow this mixture to remain in stand still for 5 – 10 minutes.
What can I use to thin epoxy?
Method #2: Thinning Epoxy Resin Using a Solvent Solvents like denatured alcohol, lacquer thinners and acetone. All of these solvents are easily available and also do a great job in lowering the viscosity. Also, these solvents evaporate quickly and are unlikely to become trapped in your cured epoxy resin.
Can you thin epoxy with mineral spirits?
3. Denatured Alcohol. Denatured alcohol is ethanol that has been made poisonous, but it’s a solvent that is safer to use as resin thinner than paint thinner or acetone. It’s properties also allow you to thin the epoxy more without as much detriment to its protective nature.
Will acetone damage cured epoxy?
Use enough acetone to soak into the surface a bit. Be careful not to damage the wood/concrete as you use your knife or scraping tool to gently and slowly scrape off the epoxy resin. There is no need to worry about any wet areas left by the acetone as it will evaporate on its own.
What is the next step after epoxy primer?
1. Sand, recoat with epoxy primer again, sand, and spray with paint. 2. Sand, lay down some 2k primer, sand, and spray with paint.
What color is epoxy primer?
A primer makes the concrete ready for the next stage. Whereas, the ‘Indigo Paints’ epoxy primer is a sealer that binds the concrete with the paint. A primer is mostly white or neutral in colour.
Where do you apply epoxy primer?
Epoxy primer refers to a sealer that has a non-porous finish. It is primarily recommended as the first base coat over bare steel. These base coats or epoxy primers can be used over fiberglass, plastic or the black iron phosphate coating as well.
How many coats of epoxy primer do I need?
The epoxy primer should be applied in medium wet coats, allowing a half an hour between each coat at around 70 degrees. One to two coats will render a one millimeter dry film thickness, which is typically enough to be completely effective.
Is epoxy primer safe to spray?
When an epoxy primer is sprayed and is airborne it should be treated with the same respect as a 2 pack paint. Required Protection: If you’re spraying (or near someone spraying) epoxy primer then you need full respiratory protection. Check with the manufacturer of the primer to see what you need).
How soon can you paint over epoxy primer?
Epoxy primer has a 72 hour re coat. Product sheet says recoat after an hour I think. Spraying DBU base coat over that. Got done with epoxy about half an hour ago, so will wait another hour or two and shoot the base.
How do you thin TotalBoat epoxy?
TotalBoat Penetrating Epoxy can be thinned up to 100% with acetone, denatured alcohol, or lacquer thinner*. Always mix the resin and hardener epoxy components together prior to adding any solvents.
Why is my epoxy so thick?
Temperature The ideal room temperature for mixing ArtResin epoxy resin is between 75 and 85 degrees F or 24 – 30 degrees C. If it’s colder than that, the resin will be thicker and harder to mix, will have more bubbles and will take longer to cure until it’s dry to the touch.
What is the solvent for epoxy?
You can use isopropyl alcohol, also known as isopropanol, to remove uncured epoxy resin. Since liquid resin is not yet that hard, removing epoxy with acetone or vinegar also works well.
Can I thin epoxy with xylene?
Xylene – Xylene is very compatible with epoxy and is often used by the manufacturers to thin resins and hardeners to the right consistency. If you look on the side of a Xylene container, you will find that a recommended use for Xylene is to clean and or thin 2-part epoxy paints etc.
What does spraying alcohol on epoxy do?
Spraying a fine mist of acetone, or another denatured alcohol, over the surface of an epoxy floor coating will pop air bubbles as well as lower the viscosity of the surface and flatten it out. A fine mist is required for this method to get rid of bubbles.
How do you remove hardened epoxy?
Method 1: Soak the metal with the epoxy glue on it in a container of rubbing alcohol (isopropyl) or an acetone-based nail polish remover. Unwrap the item and scrape off the loosened epoxy with a scraper. If you notice a bit of a haze is left after cleaning, wipe it away with paint thinner and a rag.
Can you clean epoxy with acetone?
Use acetone. Acetone can be effective on wood or concrete surfaces. It should loosen the epoxy, so you can peel it away easily. Use acetone only in well-ventilated areas and keep it away from any flammable objects.
How do you remove uncured epoxy?
Remove uncured or non-curing epoxy as you would spilled resin. Scrape as much material as you can from the surface using a stiff metal or plastic scraper. Warm the epoxy to lower its viscosity. Clean the residue with lacquer thinner, acetone, or alcohol.
