Table of Contents
What kind of plywood would you use on roof?
Exterior Plywood is the preferred material for roofing. It also performs well when exposed to moisture over long periods of time. The price is low compared to other roofing materials and the installations are also easy.
What thickness of plywood do you use on a roof?
Minimum Thickness Most roofs will be sheathed in plywood at least 3/8 inch thick. That will suffice on a roof with rafters set 16 inches apart with minimal roof loads. Loads will vary with the pitch of the roof; the flatter the roof, the greater the load on any one section.
What grade of plywood is used for roof sheathing?
1/2 or 3/4-inch Plywood for Roof Sheathing? – Traditionally, 1/2-in CDX plywood was common choice with 24-in rafter spacing. However, heavier roof loads may require the use of 3/4-in CDX plywood for roof sheathing. Roofs with less pitch often carry heavier loads, including snow and ice accumulations in the winter.
What type of wood is used for roofing?
OSB (oriented strand board) is the most common type of decking used on roofs today. It’s made up of wood chips/strips compressed together to form a flat 7/16” sheet. Plywood comes in several different thicknesses (⅜”, ½”, ⅝”, and ¾”) depending on the span of the rafters.
What should I use for roof sheathing?
Typical types of wood used for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, with no edge support, can be used in an area where the snow load is 30 pounds per square foot. With edge support and the same snow load, 3/8-inch OSB can be used.
How thick should plywood be for a shed roof?
Plywood thicknesses for roofs start at 3/8” in areas with light load requirements on rafters at 16” centers. Thicknesses of 1/2 to 5/8 inch are common with rafters spaced at 24” centers. For heavy load rated areas, 3/4-inch-thick plywood is recommended, regardless of rafter spacing.
What is better for roofing OSB or plywood?
Plywood Holds the Moisture Advantage Over OSB When plywood gets wet, it tends to swell. OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
Can you put new plywood over old on a roof?
The new plywood will have to be nailed to the rafters or roof trusses. But, with the old plywood left in place, it will be considerably more difficult to locate the rafters to ensure proper nail placement.
How thick should my roof sheathing be?
Sheathing Thickness The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch.
Is 7/16 OSB OK for roofing?
Standard types of wood designed for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, without edge support, can be used in an area where the snow load is 30 pounds per square foot.
Is CDX plywood good for roof sheathing?
Moisture Differences In reality, CDX plywood can only withstand water for a short period of time. Do not use CDX for roofing, sheds, or other places that are exposed to moisture consistently. The sole exception to this is pressure treated CDX, which can survive for decades without even a protective coating.
How thick should roof OSB be?
Standard roof sheathing thickness is ½” to ⅝” thick. If you are using OSB for your roof deck, then ⅝” is the recommended thickness. For plywood, which is slightly stronger than strand board, ½” thick is appropriate. Another factor is how far apart your trusses or rafters are spaced.
How much is a sheet of roofing plywood?
The thicker the plywood your roofer uses, the more expensive the job will be. Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood.
Can I use screws for roof sheathing?
Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.
Should you use tongue and groove OSB for roof sheathing?
Tongue & Groove Boards T&G roof decking, however, looks classy and rich. In fact, T&G boards are most frequently used when the sheathing is visible from the inside such as in cathedral ceilings or in some cabin-style homes, especially if the span of the rafters is greater than 2 feet.
Do you overhang roof sheathing?
Measure up the rafter 45-3/4 inch from the cut end of the truss tail and snap a line along the trusses. This indicates the upper edge of the first row of roof sheathing—leaving enough overhang that the subfascia and fascia will tuck neatly underneath when the time comes.
What is the cheapest way to roof a shed?
In most cases, MSR roll roofing is the cheapest shed roof material you can buy. Roll roofing is also the easiest shed roof to install because you can cover large areas quickly by simply rolling it out and nailing it down.
How many sheets of plywood do you need for a roof?
Divide the total roof area by 32 to get the number of sheets you will need to cover the roof. A typical 4 foot by 8 foot sheet of plywood covers 32 square feet. If your roof area is 1,600 square feet, 1,600 divided by 32 will mean you need about 50 sheets to cover the roof.
What is the best wood for a shed roof?
thick plywood works well for wall and roof sheathing, but use at least five-eighths in. plywood for your shed floor. Ordinary exterior-grade plywood is made with weather-resistant glue, but the wood itself is not particularly rot resistant. This is why pressure-treated plywood is best for a shed floor.
