Table of Contents
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner’s manual suggests alternatives.
Can you use regular motor oil in a chainsaw?
Chain saw bar and chain oil isn’t rated by SAE like traditional automobile motor oil. If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can you use 10w30 oil in a chainsaw?
Normally, you would need to use bar and chain oil to lubricate your chainsaw because this type of oil was specifically formulated to be used on chainsaws. As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil.
Can I use 2 stroke oil as bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
What is the difference between chainsaw oil and motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can I use wd40 on chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
Can you use old motor oil for chainsaw bar?
Yes you can in a pinch, but motor oil is much thinner than bar oil and you will use it very fast. Chainsaw bar oil is thick and sticky and is designed to be used on bars and chains.
What else can I use for chainsaw bar oil?
Use canola oil – Canola oil is currently the most common environmentally compatible chain-and-bar lubricant. Canola-based chain and bar oil has been extensively tested in Europe.
What can I use in place of bar oil?
Chainsaw Bar And Chain Oil Alternatives Motor oil. If you find yourself in a situation where you need to use your chainsaw but you don’t have any of the correct oil, one of the obvious options is motor oil. Vegetable oil. Canola oil. Drained hydraulic fluid.
What weight is bar oil for a chainsaw?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use olive oil in a chainsaw?
Other vegetable oils most commonly used in chainsaws: Olive oil – thicker than canola but not good at low temperatures. Sunflower oil – thinner than regular chain oil.
Is all chainsaw oil the same?
Chainsaw oil is not always the same, but you’ll typically be looking at a proprietary blend of refined mineral oils. This will also include inhibitors for oxidation and anti-wear corrosion, plus it will have a high tack additive included to help the oil stick to the bar and chain while it’s in operation.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated. Electric chain saws use the same type of lubrication for the bar and chain as gas-powered chain saws.
Do you need bar and chain oil?
You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.
How often should I oil my chainsaw?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
Can you use vegetable oil in a chainsaw?
VEGETABLE OIL FOR LUBRICATING CHAIN SAWS. To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant.
