Table of Contents
What is the best tool to use to cut laminate flooring?
The jigsaw is the best power tool to use to cut laminate floors with for a few reasons. It’s light, important because you’ll be picking it up all day. Also, the best blades are cheap.
Can you cut laminate flooring with a blade?
A Carbide Tipped Blade or Carbon Steel Blade is best for cutting through laminate flooring. Most utility knives and linoleum knives in the market have these material compositions for their blades. Work through your laminate floors with a carbide tipped blade and cut with ease.
What blades cut laminate?
To get a clean cut without replacing the blade repeatedly, it’s important to find a product with a thin blade width, or kerf. The best saw blade for cutting laminate flooring also should have a carbide, titanium, or diamond tip to help the blade move through the rough material.
What do you use to cut laminate flooring?
In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter. However, using a diamond blade is recommended as laminate can be tough to cut through and may damage another type of blade. Typically, you will cut with the finished side up.
How can I cut laminate flooring without chipping?
How to Cut Floor Boards Without Chipping Mark and measure where you want to cut the boards beforehand with chalk or pencil. Keep your board in place using a stand or a clamp. Wear goggles, a mask, and gloves. Use a table or circular saw to make long, straight cuts. For angles, use a utility knife or a jigsaw.
How can I cut laminate without chipping?
You can minimize the potential for chipping if you use a finish blade with lots of teeth, making sure the sharp is keen. You can further reduce the chance of chipping by using masking tape along the cut line and cutting through the tape. As with all cutting, measure at least twice and mark the line well and clearly.
Do you cut laminate flooring face up or down?
4. Sawing laminate. If you’re sawing laminate with a hand saw, make sure you turn the good-looking side up. If you’re using a saw blade made for laminate, however, you should saw wit the good-looking side up, since a laminate saw blade as upside-down teeth, which means it splinters downward.
How do you cut laminate with a utility knife?
When using a utility knife, it’s important to create a straight line while you cut. This will prevent any chips in the surface of the Formica. Also, be sure to cut the formica countertop facing down, to prevent chipping. If you cut it facing up, the coating is made out of silicone, so chipping will be likely to happen.
Can I use circular saw to cut laminate flooring?
A Circular Saw: You can also use a circular saw but it will require additional tools like a square and some type of work surface to cut the laminate flooring on. Sawhorses and a piece of plywood would make a pretty ideal workbench for this task and would be the easiest and most convenient method, in my opinion.
How many teeth blade for laminate flooring?
Blades for Laminate Flooring In view of this, a thin kerf, 80 to 100 tooth, carbide-tipped blade is most effective for cutting laminates and will last for about 1000 sqft before needing to be re-sharpened.
How do you cut laminate flooring on the floor?
Plunge the saw blade into the laminate flooring. Let go of the blade guard and allow it to snap into place. Cut along the chalk line beginning at one end of the line and ending at the other end of the line.
Do you cut the tongue off the first row of laminate?
Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. If it is too short, cut a new plank in half and use one half to start the second row.
Do you cut laminate flooring upside down?
4. Sawing laminate. If you’re sawing laminate with a hand saw, make sure you turn the good-looking side up. If you’re using a saw blade made for laminate, however, you should saw wit the good-looking side up, since a laminate saw blade as upside-down teeth, which means it splinters downward.
Does laminate flooring dull saw blades?
You see, laminate flooring will destroy a wood cutting blade with alternating top bevel (ATB) teeth in no time at all. The sharp points on this type of blade can’t handle anything that hard – they dull quickly and those tips are what the blade uses to cut cleanly through wood.
Can I cut laminate with a jigsaw?
Jigsaw: A jigsaw is a real all-rounder when it comes to cutting laminate floors. It’s best used to cut out shapes from your board. For example, when you want to place boards around your toilet or maybe a pillar.
How do you cut Wilsonart laminate flooring?
To precut Wilsonart RE-COVER laminate prior to bonding, we recommend using carbide tipped saw blades, router bits and laminate slitters. Cutting blades and router bits should be kept sharp and clean. laminate face down (adhesive side up) to ensure a clean cut.
