Table of Contents
What is Wedging? Wedging prepares the clay for optimal use. Wedging makes the clay more pliable, ensures a uniform consistency, and removes air pockets as well as small hard spots in the clay before you use or reuse the clay for a project. When reclaiming clay, wedging ensures all the clay is incorporates together.
What is wedging in clay preparation?
Wedging clay definition: the process of kneading the clay with the hands to remove air bubbles and ensure a homogenous mass. A fun exercise to see how long it takes to crate a truly homogenous mass of clay is to wedge together two chunks of different colored clays.
When should you wedge clay?
You should wedge at least 30 times when it’s fresh out of the bag. When it’s recycled clay, you will need to wedge it at least a 100 times if not more depending on the condition of your clay.
Can you pre wedge clay?
If you let your clay dry enough before firing you wont get an explosion, but an air pocket in your peice will show up very soon while wheel throwing pottery and it will mess up your piece. You will have a physical bulge that looks like a bubble and messes up the contours of the piece.
What is the difference between wedging and kneading clay?
Wedging is a specific type of kneading. The goal with wedging is to mix the clay without adding air bubbles. If you do it correctly, you’ll remove air bubbles. I was taught two types of wedging- knead (or ram’s head) and spiral.
What should I put down when working with clay?
If you want to continue working on a piece another time, please wrap it up very well with some sheets of plastic, or put it in a well sealed plastic box, then put it somewhere out of direct heat or sunlight. This should slow down the drying of the clay to enable you to keep working on it.
What is the best surface for wedging clay?
Every potter needs a surface to wedge clay on, and there are many different types. The most common are plaster, plaster covered in canvas, and plywood covered in canvas. Other possibilities are concrete, granite, masonite, concrete board and hardibacker board. The simplest wedging surface is a piece of canvas.
What are the six stages of clay?
There are 6 essential stages of clay: 1. ) Slip. Slip is clay with added water to make it into a paste or liquid. 2.) Wet clay. Wet clay is used by many potters to produce their work. 3.) Leather-hard clay. 4.) Dry clay. 5.) Bisque. 6.) Glaze ware.
What are the 5 stages of clay?
Terms in this set (5) slip. a mixture of clay and water, the consistency of pudding. wet/plastic clay. new clay from the bag, very workable. leather hard. the clay has lost most moisture, but you can still carve into it. bone dry or greenware. totally dry clay, all moisture is gone, ready to fire. bisque.
Is there a machine that wedges clay?
A Pugmill is a machine with a horizontal chamber that loads on the top. The chamber is a metal cylinder with an auger inside. An auger looks like a large screw. It turns and wedges the clay, discharging the wedged clay at the other end.
Is wedging clay necessary?
Wedging is an essential part of making with clay, it is a process which prepares your clay so that you can successfully make with it. It is the process of removing any air from within the clay.
Do air bubbles cause clay to explode?
A thin piece of clay with an air bubble will dry and fire without issue. When the kiln temperature rises, the air pockets fill with water vapor, which builds pressure as water turns to steam. The pressure of the steam causes the clay to explode from the inside.
Why does my polymer clay bubbles after baking?
Those bubbles are caused by trapped air in your polymer clay. When you fold over your strip of clay and insert it in your pasta machine fold last, a little pocket of air gets trapped in the fold. If you keep doing this over and over, more and more air gets forced into the layers of clay.
What’s the purpose of wedging clay?
Wedging prepares the clay for optimal use. Wedging makes the clay more pliable, ensures a uniform consistency, and removes air pockets as well as small hard spots in the clay before you use or reuse the clay for a project. When reclaiming clay, wedging ensures all the clay is incorporates together.
What surface does clay not stick to?
Most air dry clays are sticky, and you don’t want that on your work surface. We recommend protecting the work area with items such as wax paper, silicone baking mats, or vinyl placemats. This will keep your table protected and make clean up much easier!Mar 8, 2018
What happens if there is an air bubble in clay?
Air bubbles in clay items are dangerous because they can cause explosions in the kiln. The air bubble dilates due to heat and forces the clay to crack or explode and shatter the ceramic piece. The risk of explosion increases with the temperature in the kiln.
What happens if you don’t wedge clay properly?
There are usually no air bubbles in it! In fact, improper wedging will more often add bubbles and you’ll just dry out your clay in the process. Simply make sure the pieces get enough drying time and have no plaster mixed in with the clay- that IS a sure recipe for explosions.
How do you wedge a large amount of clay?
If you’re throwing large pots, try using softer clay and throw it dry (or with less water) to avoid degenerating it to mush. Wedge using the weight and strength of your whole body on a wedging table of the proper height. Ideally, the table height should be equal to the distance between fingertips and floor (figure 1).
