Table of Contents
Toilet Rough-In Measurements and Standards Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s best to perform this measurement before you remove the old toilet.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
How do you determine toilet rough-in?
The rough-in measurement of a toilet refers to the span between the wall behind the toilet and the center of the waste pipe. To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor).
Can you replace a 14-inch rough-in toilet with a 12-inch rough-in toilet?
You can, but the back of the toilet tank will be two inches further away from the wall. The “rough-in” dimension refers to the distance from the wall framing (½-⅝″ behind the finished wall surface) to the center of the sewer pipe on the floor. Standard rough-in is 12 inches.
What is the difference between a 12 and 14 rough-in toilet?
The main difference between 12-inch rough-ins and 14-inch rough-ins is in their size (proportions). Depending on the type of bathroom, 12-inch rough-ins are generally more used than 14-inch rough-ins, but they both have merits, which means that you sometimes need to reduce the space from behind the tank.
Can you replace a 10-inch rough in toilet with a 12 inch rough in toilet?
The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
Do all toilets have a 12 inch rough in?
Most toilets will have a 12 inch rough-in. Toilets with a 10- or 14-inch rough-in measurement are a little less common, so you might have less of a selection of toilets of this size. If you’re replacing an existing toilet, look for a replacement toilet with the same rough-in.
What does 12 rough in mean for toilet?
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. Rear-outlet toilets are configured a bit differently.
What is rough in?
: to make a rough or unfinished version of (something, such as a design) as the first step in creating the finished version Rough in the lettering on your poster.
How far from the wall should a toilet rough in Be?
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall. Don’t measure from the base molding! Take this measurement from the finished wall.
Does rough-in size matter?
Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. If the base of the new toilet is shorter than the distance between the rear bolt holes and the wall, it should fit.
How many inches does an offset toilet flange move?
The typical offset is 12-inches for most residential toilets. As a result, the toilet had 4-inches behind the tank. It looked like it was trying to participate in the activities of the bathroom rather than sit quietly until needed.
Can you replace a 13 inch rough-in toilet with a 12 inch rough-in toilet?
That’ll be your rough-in. If your distance if 13″ and you have a 1″ gap between the tank and the wall, then yes, your existing toilet is probably a 12″ toilet. You can indeed have two 12′ toilets that differ in size from one another.
Why would I want an elongated toilet bowl?
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
What measurements do you need to replace a toilet?
Make sure you measure from the centre of the bolts, up to the drywall (as opposed to the baseboard). If there are four bolt caps, be sure to measure from the center of the rear set. Toilets come in 10”, 14”, and most commonly, 12” rough-in dimensions.
How do you move a toilet closer to the wall?
Install the Offset Flange Positions the offset flange so that the bent end moves the flange opening closer to the wall. Make sure the back of the offset flange connects snugly with the drainage pipe. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.
What does 10 inch rough-in toilet mean?
When you wonder about ‘what a 10-inch rough-in toilet means’, it refers to the finished wall and the floor flange opening center distance of about 10-inches. 10-inch rough-in is usually found in the old models’ homes. Although, there are only fewer toilets options available.
What is an ADA toilet?
A comfort height toilet is sometimes known as an Americans with Disabilities Act (ADA) toilet because the height matches that used for ADA-compliant toilets, 17 to 19 inches from floor to seat. This is like the height of a chair. The height of a standard toilet is about 15 inches from floor to seat.
