Table of Contents
W – This is the thermostat terminal for heating. This wire should go directly to the heating source whether it be a gas or oil furnace, electric furnace, or boiler.
Where does w wire go on thermostat?
The white wire underneath your thermostat connects to your heating system. It terminates at your air handler or furnace. The white wire connects to terminal W in industry-standard thermostats.
What color is the W wire on a thermostat?
White Marking Wire Color Code Description W White Primary heat cell relay E Brown Emergency heat relay Y Yellow Primary cool call relay Y2 Yellow Secondary cool call relay.
What does R and W mean on thermostat?
W wire – heat. R wire – heat power. W wire – heat.
What’s the difference between W1 and W2?
In a conventional system, W/W1 controls your heating system and, where applicable, W2 controls your heating system’s second stage, which helps warm the home faster. In conventional cooling systems, Y/Y1 controls the first stage of cooling and Y2 controls the second stage, which helps cool down the home faster.
What happens if you wire a thermostat wrong?
Potential consequences of improper installation could include: Electric shock. Blowing a circuit breaker. Damaging the thermostat unit, the electrical system or even the AC/furnace unit itself.
What do the different color wires mean on a thermostat?
This is the most typical thermostat wiring style, and it applies to systems that regulate both heat and air conditioning. The wires are typically arranged as follows: red for 24-volt hot, white for heat, yellow for cooling, green for the fan, and blue for common (although the common wire may be a different color).
What color is the reversing valve control wire normally?
Traditional Thermostat Wire Color Codes Color Terminal Use Green G Switched to Fan Orange 1 O Switched to Reversing Valve Yellow Y Switched to Cooling.
What does W wire do?
The W or W1 wire controls your heating system. In most systems, the Y or Y1 wire controls your cooling system. If you have a heat pump, your Y or Y1 wire controls your compressor. Your compressor is responsible for heating and cooling your home.
Where does W2 wire go on Nest?
If you have a W2, Y2 or O/B wire, you can put it into the *O/B connector, if needed. Gently tug each wire to check they’re secure, and make sure each connector that has a wire stays down. Push the display onto the base until it clicks. Download the free Nest app so you can control your thermostat with your phone.
What is B terminal on thermostat?
W/B: The W/B terminal controls the heat relay or valve. When the thermostat calls for heat, a signal is sent to power up the furnace and the blower fan or the boiler, heating your home.
What is W2 on furnace?
W2 – This is the thermostat terminal used for second stage heat. There are gas furnaces with low fire and high fire and some depend on control from a two-stage heating thermostat with a W2 terminal. Heat Pumps use staging for auxiliary heat and need a W2 terminal.
Does white wire go to W1 or W2?
Thermostat White Wire (“W1” or “W2” Wire) W wires go directly to the source of heating; that may be a furnace (gas, electric, oil, you name it) or heat pumps (mini-split heat pumps included). W2 is designated for two-stage heating. Most heat pumps include second-stage heating and require the white W2 wire.
Is W2 and e wire the same?
1-3 of 3 Answers. E and W2 wires are connected to the W2-AUX/E terminal together. In the south where I live E is for emergency heat and W2 is for second stage heat. Wiring can vary based on different systems; in some instances, you can not connect the E wire to the thermostat.
Should my thermostat be on E or F?
The thermostat fan operation switch, labeled FUEL SWITCH in the diagram below, is factory-set in the “F” position. This is the correct setting for most systems. The “E” setting will allow the fan to turn on immediately with the heating or cooling in a system where the G terminal is connected.
What are the four wires in a thermostat?
In general, the heating wire (often white), goes into the “W” port, the cooling wire (often yellow), goes into the “Y” port, the wire that sends power from the HVAC system to the thermostat (often red), goes into the “R” port, the fan wire (often green), goes into the “G” port, and the common wire (often blue), which.
Does thermostat need jumper wire?
Nest thermostats don’t use jumper wires Putting more than one wire into a Nest thermostat connector can damage your system and your thermostat. Instead of using jumper wires, Nest Learning Thermostats use an internal jumper between the Rh and Rc connectors.
How do you turn off the override on a thermostat?
Once you have selected the temperature, simply press the Hold button to keep the thermostat saved. This displays the word Hold on the screen and maintains that temperature indefinitely. If you want to resume the normal programmed temperatures, press the Run button to cancel the override.
Can I turn my heating on without thermostat?
Do you need a thermostat for your boiler? In short: yes. Your boiler thermostat is essential if you want to be able to control the temperature of your central heating and hot water. It’s called the Boiler Plus legislation, and applies to all gas and oil boiler installations.
What color wire goes where on a Honeywell thermostat?
Meaning of Wiring Terminal Letters W (white) controls the auxiliary heating elements. Y (yellow) controls the compressor on the cooling system. G (green) controls the fan. C (blue or black) provides a return path to the transformer.
What does S1 and S2 mean on a thermostat?
The S1 and S2 terminals on the Honeywell are for a remote optional sensor. Your Honeywell may have been using the S1 and S2 terminal to determine when to switch from heat pump to gas.
