Table of Contents
The IRC requires guardrails to be at least 36″ in height measured from the deck surface to the top of the rail. Commercial decks attached to multifamily buildings regulated under the International Building Code (IBC) require 42″ high guardrails.
What is code for deck railing posts?
U.S. building code requires support posts for the rail structure to be no further apart than 6 feet on a deck with 4×4′ deck rail posts and no more than 8 feet apart for decks with 6×6′ deck rail posts. Posts should be no further apart than 5.5 feet on stairs.
What is code for railing height?
Handrail Height: 34 to 38 Inches Handrail height on the stairs should be no less than 34 inches and no greater than 38 inches. The way this is measured is to begin at the leading edge of the stair nosing and run an imaginary vertical line upward until it reaches the top of the railing.
Can you notch a 4×4 deck railing post?
Say “No” to notching pressure-treated deck posts. We want you to build an outdoor railing system that you, your family and guests can enjoy without worrying about safety issues. In order to do so, you need to know this building shortcut is not advisable, and we recommend avoiding it at all costs.
What is residential handrail height?
Handrails must be 34 to 38 inches high.
How many risers before you need a handrail?
Building Codes The building code does not refer to the number of “steps” but it does require a handrail when there are two or more “risers”. For clarification, a “riser” is the vertical portion of a stair. The “tread” is the top of a step. A two riser minimum would translate to two steps.
Do you need a railing for 3 steps?
A: Editorial Adviser Mike Guertin replies: Since your stairs will have only three risers, you don’t need to install a handrail. That said, it’s important to count the number of risers accurately.
Can balusters be used in place of posts?
T/F: Balusters can be used in place of posts if there is adequate infill between them. T/F: End-grains of vertical posts and balusters should be cut level. Deck planking segments should bear on a minimum of _____ joists. T/F: Deck planking should be laid together as tightly as possible.
Can a 2×4 be used as a handrail?
According to the IRC (2018), you can use a 2×4 to make a handrail, but you must cut finger recesses along both sides of the board and position the lumber lengthwise on its end. Using a 2×4 as a handrail laid vertically is not allowed. Porch and deck guardrails made from 2x4s laid horizontally are permitted.
How do you attach a railing to an existing deck?
After the decking is finished, it will be time to install the top and bottom rails, balusters, top cap and any other parts. Mark rail post centers. Mark for the exact position. Cut the post and tack a guide nail. Plumb and clamp the post. Drill holes for the bolts. Pound the bolts through.
How do you tie 2 4×4 posts together?
To connect 2 4x4s use a half-lap joint secured with construction adhesive, two steel plates, and four to six 1/2″ or 5/8” through bolts. Posts that support roofs or platforms should lap between 20” and 24”, other structures should connect for 6” to 10” along the centerline.
At what height does OSHA require guardrails?
However, in OSHA applications, the elements are most likely horizontal rails. So, the term is appropriate. A guardrail is required once there is a 48-inch drop. As opposed to the requirements of handrail system, a guardrail must be 42 inches in height – plus or minus 3 inches above the walking surface.
Do I need a handrail on both sides?
Handrails are required on both sides of stairs and ramps. They are placed between 34 inches and 38 inches above the leading edge of a stair tread, the ramp surface, or the walking surface. Where children are the primary users of a facility, the ADA recommends a second handrail for children.
Is it illegal not to have a handrail on stairs?
Handrails are mandatory. Stairs should have a handrail on at least one side if they are less than one metre wide, and on both sides if wider than this. Handrails should be placed between 900mm and 1000mm above the highest point on the staircase steps.
Do deck stairs need railings on both sides?
Do I Need Handrails On Both Sides of Deck Stairs? Nope. You don’t need a handrail on both sides, but you may need a railing if your deck is higher than 30″. Many contractors construct a combo handrail and stair rail system, installed on both sides, to cover all safety requirements.
What is the code for outdoor steps?
Exterior Stair Construction The rise of the stairs should be between 125 mm (5”) and 200 mm (8”). This is measured from top of a tread nosing to the top of the next tread nosing or landing. The run should be between 210 mm (8 ¼”) and 355mm (14”). Unit run is measured from face of nosing to face of nosing.
Are risers required on deck stairs?
Most high-end deck projects use closed risers to finish the stairs. They also are often in violation of IRC code for decks over 30″, which maintains that they meet the same requirements as guardrail infill. Stair risers may not have openings present that would allow a 4” diameter sphere to pass through.
How far apart should deck balusters be spaced?
Balusters are the vertical guards that support the handrail. They must be installed close enough that the space between them is less than 4 inches. Most city inspectors carry a 4-inch ball with them to test the spacing. Installed balusters should withstand 50 pounds of pressure exerted over a 1-sq.
How far apart should deck posts be?
In general, posts should be spaced no more than 8 feet apart. Some builders position them every 4 feet for a completely rigid frame. The maximum distance between footings is determined by the size of your joist material.
