Table of Contents
The most common RPM is 1200 (1050 or 1075) also 900 (850, 825) and 1550 are used too. Most motors are single speed but can have as many as 4 speeds (3 is typical for direct drive indoor blowers on most furnaces).
What speed should furnace fan run?
While most models of furnace fans are capable of moving at 1,200 revolutions per minute (RPM), some spin at a slower rate. For residential furnace installation units, the maximum speed of most fans is typically 1,500 RPMs.
How do I adjust the blower speed on my furnace?
When increasing the blower speed, loosen the setscrew a little bit. This is the part that holds the pulley to the furnace’s driveshaft. Turn the pulley one rotation clockwise on the shaft. If you want even more speed, do two rotations.
How do I adjust the blower motor speed?
You can increase or decrease the blower speed by slightly adjusting the pulley on the blower drive motor. To increase blower speed, slightly loosen the setscrew that holds the pulley to the driveshaft. Move or turn the pulley clockwise on the shaft one turn, then tighten setscrew.
Can I put a bigger blower motor in my furnace?
Yes, you can place a bigger blower motor in your furnace.
How much power does a furnace fan use?
Typically, a standard blower fan needs on average 400 watts of electricity. This means that it needs a 15-20 amp circuit. However, depending on the size of your furnace, the amount of needed power could be 20 amps or more.
How many speeds does a blower motor have?
A standard blower motor only has one speed; it is either fully on or fully off.
What fan speed should I use?
In general, the slower the air speed, the better the cooling since the air spends more time on the evaporator. The tendency is to use the highest speed, to get a higher volume, but that will result in a less colder air. The answer is really simple, whatever speed the unit was designed to run at.
What color is high speed on a blower motor?
white to red, White to Blue. The Higher the resistance, The slower the speed. Black is “generally” HIGH speed. Red Is “generally” the lowest speed.
Is variable speed furnace worth it?
The best news … a variable speed furnace motor is 80–85% more efficient than a standard furnace motor. If you don’t have a 90% efficiency or higher furnace in your home, then yes it may well be worth the cost to upgrade.
How does a variable speed furnace work?
Variable speed furnaces are able to run at a range of speeds, rather than one speed as traditional furnaces do. The differing speeds control heating and cooling airflow through the home. Throughout operation, the furnace monitors incoming data from your HVAC system to automatically make blower motor speed adjustments.
How do I change the fan speed on my Tempstar furnace?
Locate the furnace control board on the bottom half of the air handler, centered. Locate the terminal marked, “heat,” on the control board. Slide off the speed tap wire attached to the heat terminal and replace it with the wire color that matches the desired speed.
Can I put a more powerful fan in my furnace?
Yes, you can change your blower motor’s speed to try and improve your airflow if your blower motor is not already at the highest speed.
Can I upgrade my furnace blower to variable speed?
When upgrading your furnace, consider adding a variable speed furnace blower motor. It can improve the efficiency of your heating system while making your home more comfortable. For example, they often start at about two-thirds speed; if heating is still needed after 10 minutes, they increase to full speed.
Does running the fan on my furnace use a lot of electricity?
Most fans are quite energy efficient, especially in newer systems. The fan itself runs about as much energy as a refrigerator would. This can still add up to $50 a month, or $600 a year. This cost can be even higher if you consider the AC unit working harder to counteract the effects the fan may have.
Does an electric furnace use a lot of electricity?
Cook a meal on an electric range -using all the burners and the oven – for about 84 cents an hour.How much electricity does your appliances use? Appliance Typical Wattage Estimated Average Cost Electric Fireplace (heating mode) 1500 15¢/hr Forced Air Systems 15 kw Central Electric Furnace 15,350 $1.5323/hr 20 kw Central Electric Furnace 20,490 $2.00/hr.
How much electricity do blower fans use?
A typical AC fan motor uses about 500 watts when it’s running. Therefore, if you run the fan continuously for a 30-day month (720 hours), you would use 360,000 watt hours (720 x 500) or 360 kilowatt hours (kWh). Therefore, the fan uses about 360 kWh per month in the ON mode.
Does a variable speed furnace run all the time?
Variable speed furnaces have an air handler that operates at many different speeds depending on the demand for air at any given time. A variable speed air handler runs almost all the time, albeit typically at a low setting that is much quieter than the higher setting that’s used during heating cycles.
What is a multi-speed ECM blower motor?
Rather than operating on the all-or-nothing principle, multi-speed blowers run at different velocities according to the temperature requirements of your home. They power up at full throttle and switch to a lower speed to maintain the desired temperature.
What is a multi-speed furnace?
Multi-speed furnaces, also known as multi-stage or variable-speed furnaces, run at several energy levels. Multi-stage furnaces can cut the blower capacity down to as low as 40 percent, so you can have just the level of heat you need and save money and energy.
