Table of Contents
“Slip” in an AC induction motor is defined as: As the speed of the rotor drops below the stator speed, or synchronous speed, the rotation rate of the magnetic field in the rotor increases, inducing more current in the rotor’s windings and creating more torque.
What is normal slip of an induction motor?
Because of this speed difference, the motor rotates at a speed slightly slower than the synchronous speed. Slip is normally expressed in percentage. Slip of a power induction motor is 2 to 3% when the motor is operated under the rated load.
What is slip and slip speed of an induction motor?
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
What is the maximum value of slip in induction motor?
It is common to express the slip as the ratio between the shaft rotation speed and the synchronous magnetic field speed. When the rotor is not turning the slip is 100 %. Full-load slip varies from less than 1 % in high hp motors to more than 5-6 % in minor hp motors.
What is Torque slip?
The torque slip curve for an induction motor gives us the information about the variation of torque with the slip. The slip is defined as the ratio of difference of synchronous speed and actual rotor speed to the synchronous speed of the machine.
What happens if slip of induction motor is 1?
When the Value of Slip is >1 If the slip value of the motor is greater than one then the rotor will turn in the opposite direction to the revolution of magnetic flux. So if the magnetic flux is revolving in the direction of clockwise, then the rotor will turn rotating in the anti-clockwise direction.
Can slip be negative?
From the above equation it is clear that, for slip to be negative, the rotor speed should be greater than synchronous speed. Hence,Negative slip is a situation when an induction motor becomes an Hence,Negative slip is a situation when an induction motor becomes an induction generator.
Which type of motor is mostly used in the industry?
The majority of industrial motors are three-phase AC induction motors due to its reliability and low cost. In this case, the electric current in the stator winding generates a rotating magnetic field that “induces” (hence the name) electric current in the rotor.
How is slip in motor calculated?
Slip speed is the speed difference between the Synchronous speed and Rotor speed. Slip speed = Synchronous speed – Rotor speed = Ns -N. Slip, s = (Ns – N) / Ns.
What will happen when the slip is 100 and zero?
What will happen when the slip is 100 and zero? As the rotor ends are short circuited current flows through the rotor. So when slip is zero there is no phase difference between stator flux and rotor flux and there is no torque exerted on rotor and rotor does not rotate .
What is synchronous speed?
: a definite speed for an alternating-current machine that is dependent on the frequency of the supply circuit because the rotating member passes one pair of poles for each alternation of the alternating current.
What is a high slip motor?
A high slip motor allows the torque to increase torque per amps even as the motor moves from fixed speed to the locked rotor state. Standard NEMA Design A, B, or C motors operate at one to five percent slip. A NEMA D motor has a high slip of five to thirteen percent.
What is unit of slip?
Slip is expressed in meters per second (m/s). It’s the relative speed between the wheel’s contact point and the colliding surface.
Why there is no slip in synchronous motor?
Because the rotor turns at the same speed as synchronous speed (speed of the rotating magnetic field), there is no slip. The speed of rotation of the motor is constant in a synchronous motor, and does not vary with load, as in an induction motor.
What are the types of induction motor?
Types of Induction Motors
- Split Phase Induction Motor.
- Capacitor Start Induction Motor.
- Capacitor Start and Capacitor Run Induction Motor.
- Shaded Pole Induction Motor.
What is the slip of a 3 phase induction motor?
This speed difference is called slip. Therefore, the difference between the synchronous speed Ns of the rotating stator field and the actual rotor speed N is called slip. The slip increase with load and is necessary for torque production. Slip speed is equal to the difference between rotor speed and synchronous speed.
When slip is zero rotor will?
If Slip is equal to zero, rotor current is zero and torque is zero. The zero torque means motor will not rotate at all.
Why is slip important in an induction motor?
In induction motor, slip is important because slip determines torque and also the machine behaviour. Explained as follows: (1) Torque depends on rotor power factor which, in turn, depends on slip. So, torque is lowest when slip(s) is equal to 1 i.e. at standstill.
What is slip percentage?
The difference between theoretically calculated forward speed based on angular speed of the rim and rolling radius, and actual speed of the vehicle, expressed as a percentage of the latter, is called ‘slip ratio’.
Can slip be more than 1?
Slip more than 1 implies that, rotor is rotating in a direction opposite to the direction of rotation of magnetic flux. This means if magnetic flux is rotating in clockwise direction, then rotor is rotating in anticlockwise direction or vice versa. Therefore, the relative speed between them will be (Ns + Nr).
What is 120 in motor speed formula?
The equation for synchronous speed – the speed of the magnetic field inside the motor stator is 120 x F / P where F is the applied frequency in Hz, and P is the number of poles (always a multiple of 2) in the motor winding. 120 is a constant that gives your answer in revolutions per minute.
What is slip formula?
Formula to find slip = (ns – n) x 100/ns. substitute the values in the above formulas. speed difference = 1500 – 1450. = 50. slip = 50/1500 x 100.
