Table of Contents
A sprayer. The sprayer hose on some kitchen sinks can be used for direct water spray. When the sprayer is depressed, the hose is attached between the faucet and water supply with a valve that controls where the water goes.
What is the thing in your sink called?
Stoppers: Many bathroom sinks have a drain that can be closed to keep water in the basin. These are called stoppers, and they include a fitting that goes inside the drain and a lift rod to raise and lower the stopper valve.
What is the nozzle on a faucet called?
A faucet aerator (or tap aerator) is often found at the tip of modern indoor water faucets. Aerators can simply be screwed onto the faucet head, creating a non-splashing stream and often delivering a mixture of water and air.
What is the thing next to faucet?
The valve is actually for the dishwasher and is commonly known as the dishwasher air gap. An air gap’s purpose is to prevent drain water from the kitchen sink backing up into the dishwasher, contaminating your cleanly washed dishes.
Can you replace just the sprayer on a kitchen sink?
Whether you’re installing a sink sprayer replacement or adding a new sprayer to your current kitchen faucet set-up, it’s a pretty quick and simple update. It’s also a cost-effective alternative to installing an entirely new faucet with a sprayer.
What is the rubber thing in the sink called?
A garbage disposal’s rubber splashguard, located inside the sink flange, prevents water and food from splashing up when the disposal is in use. The guard, or cover, may deteriorate due to normal wear and tear, and can be replaced.
What is a sink flange?
The flange in your bathroom sink is the collar that surrounds the sink’s drain. It is usually made of metal, but may be made of plastic and coated in a metallic finish. If this flange cracks or erodes, it can cause water to leak through the sink at this point.
What are the parts of a faucet called?
Cartridges & Stems. Aerators & Flow Restrictors. Washers & Washer Kits. Escutcheons & Flanges. O-Rings & O-Ring Kits. Caps & Index Buttons.
What is the curved pipe under the sink called?
This pipe section is called the p-trap. You might wonder why it isn’t called the u-trap because of the shape of the curve.
What are the parts of a kitchen sink drain?
A Brief Introduction Of The Kitchen Sink Drain Parts Sink Strainer. You should see the sink strainer whenever you use your kitchen sink. Tail Piece. You’ll see the tail piece just right after the strainer. Tee. A tee is a pipe that’s shaped like the letter “T”. Waste Arm. Extension Tube. Coupler. Elbow. P-Trap.
What is a sink air gap for?
An air gap is a simple way to make certain wastewater and contaminants never re-enter your clean water supply. There is enough distance between the mouth of the faucet and the sink’s rim to ensure that dirty water will never backflow into your kitchen faucet and pollute the clean water supply.
What is an air gap faucet?
Air gap faucets are designed to prevent backflow into your reverse osmosis unit by incorporating a “backflow prevention” method called an “air gap”. In the event of clogging, a small amount of air, rather than dirty water, would go back into the RO system, thus protecting the system.
What is a plumbing P-trap?
Plumbing codes require a P-trap be installed anywhere there is an open drain line that expels wastewater into a drain waste-vent system. The P-trap traps solids that can clog the drain or sewer line. The P-trap stops sewer gases from backing into your home through the drain line.
Can I disconnect my sink sprayer?
When your sprayer begins to leak from the hose, the connection or the sprayer head, you can fix it or remove it. Choosing to remove the sprayer requires capping the connection point on the kitchen faucet. It also requires capping the hole left in the sink or countertop when you remove the sprayer.
What is a disposal splash guard?
Guards the opening of your garbage disposal from unwanted debris. Prevents water from splashing when garbage disposal is running.
What is a InSinkErator garbage disposal?
InSinkErator garbage disposals and instant hot water dispensers. InSinkErator garbage disposals and instant hot water dispensers speed up kitchen tasks so that you can slow down. InSinkErator disposals quickly handle food waste to make it disappear and help make your kitchen cleaner.
Are garbage disposal baffles universal?
Garbage Disposal Splash Guard / Sink Baffle, Fits Insinkerator Disposals and Most Universal 3 1/2 inch Sinks.
What is the flange on a sink drain?
A sink flange connects the sink drain to a section of pipe called a tailpiece to create a tight seal. It is made of metal and sits around the edge of the drain rather like a collar, and it usually has a grid-like section covering the drain that looks like a strainer.
What is a tailpiece in plumbing?
The tailpiece, or sink tailpiece, is the straight section of pipe that connects to the bottom of the sink drain fitting. Typically, the tailpiece attaches to the drain fitting with a slip nut—a threaded ring that can be tightened and loosened by hand (or with gentle persuasion from channel-type pliers).
What are the three parts of a faucet?
There are buttons and caps. Faucet handles. Faucet spouts.
What is a faucet spout?
The spout is the part of the faucet that most people notice first; it’s the part that delivers water from the body to the sink and it can be distinctive in its design. A straight spout provides a long reach with a low profile. A gooseneck spout has an elegant, high-arc shape that comes in handy for filling deep pots.
