Table of Contents
Instead, the rake refers to the sloped sides of a gable style roof. This type of roof is one of the most common in colder or temperate climates, and consists of two roof sections sloping in opposite directions from the peak to allow for the best flow of precipitation off the roof.
What part of a roof is the rake?
Rake—The slanting edge of a gable roof at the end wall of the house. Ridge—The horizontal line at the top edge of two sloping roof planes. Sheathing—The decking material (usually sheets of plywood), which is nailed to the rafters, and to which shingles or other outside roofing materials are secured.
What is the difference between gable and rake?
Gable: The A-shaped side wall of the home that forms the peak of the roof is called the Gable. The home above has two gables, one on each end of the home. Rake: The rake of the roof is the part that ends over a gable end.
How do you measure a roof rake?
Place the end of the level against the bottom edge of a roof rafter and hold it perfectly level. Measure from the 12-inch mark on the level vertically to the bottom edge of the rafter. That measurement is the number of inches that the roof rises in 12 inches. Locate a rake board that is readily accessible to you.
What are the parts of a roof called?
The Architectural Parts of a Pitched Roof Roof plane: This is the surface of the roof. Ridge: This is the top or peak of the roof, where two roof planes meet. Valley: This is where two pitched roof faces connect and project inward. Dormer: This is a roof feature that projects out from the roof face.
When should you rake a roof?
If your roof is flat or has a low slope, roof raking is definitely a must once the snow gets to be about 6 inches or more. If your roof has a higher pitch, it’s still something to consider, especially if the snow is wet and heavy and it is building up.
What is a rake overhang?
The American Wood Council’s 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.
Where is the eave on a roof?
An eave is the edge of the roof that overhangs the exterior siding. Parts of an eave include the soffit, which is the underside of your roof’s eaves, and the fascia, the vertical facing board.
What is a rake in?
: to earn or receive (a large amount of money) The movie raked in over $300 million.
What is the overhang on a roof called?
Soffit: The underside of the eaves, or roof overhang, which can be enclosed or exposed.
What does a pitched roof look like?
A pitched roof is a roof that slopes downwards, typically in two parts at an angle from a central ridge, but sometimes in one part, from one edge to another. The ‘pitch’ of a roof is its vertical rise divided by its horizontal span and is a measure of its steepness. For more information, see Flat roof.
What is the normal pitch of a roof?
Conventional slope roofs are most common with residential roofs. This means the slope has a pitch between 4/12 and 9/12 on most homes. Roofs with a pitch exceeding 9/12 are called steep slope roofs.
What is a roof soffit?
The soffit is part of the overhang where your roof meets your siding. When rain or snow hits your roof, it runs down, and the overhang allows the water to flow away from your house. The soffit is underneath the overhang, between the roof’s edge and side of your home—the bottom of the triangle, if you will.
What are the parts of a roof truss?
Parts of a roof truss Apex. Apex plate. Top chord. Heel plate. 1/3 point plate. Bottom chord. Slice plate. Heel.
What are the parts of a flat roof called?
Essential Parts of a Flat Roofing System Plasterboard Ceiling. The plasterboard ceiling is the visible interior part, which covers the entire roof. Decking. The decking is the skeletal part of the roof. Insulation and Vapor Barrier. Waterproof Layer and Covering.
Why would you rake a roof?
Sometimes snow on your roof can be a good thing. Depending on snow density, your slanted roof may be able to safely support up to 2-4 feet of snow accumulation. The most common reason homeowners rake their roof is to prevent the creation (or reduce the impact) of ice dams.
Are roof rakes worth it?
Never, never use a roof rake or try to shovel snow off a slanted roof. It will do no good, will not cure ice dams, is extremely hazardous, and can harm asphalt shingles, and in your case, slate shingles. And it will take away snow that is a natural insulator as long as it stays on your house.
Does roof rake damage shingles?
Use a snow rake for pitched roofs (available at most hardware stores) to remove snow from your roof. Start from the edge and work your way into the roof. Try to shave the snow down to a 2 or 3 inches on the roof instead of scraping the roof clean, which will risk damage to your shingles or other roof covering.
