Table of Contents
Lock/Ignition Switch The ignition switch, on the right side of the steering column, has five positions: LOCK — The normal parking position. This locks the steering and prevents normal use of the steering wheel. The key can be removed only when the ignition is in this position.
What are the 4 positions of the key ignition switch?
The 4 position switch features accessory, off, on/run, and start position.
How do you know your ignition switch is locked?
First of all be sure that the ignition lock is not engaged by turning the steering wheel back-and-forth. If the key will still not turn there may be excessive wear inside the ignition that is preventing the key from properly aligning with the keyhole. If the key cannot be turned your car will not start.
What are the basic 3 positions of the ignition switch?
Conventional 3 positions are off, run, and start.
What are the 5 ignition positions?
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). Use this position only to start the engine. The switch returns to the ON (II) position when you let go of the ignition switch.
What is lock ACC on start?
ACC (Accessory) — Allows operation of electrical accessories with the engine off. ON — The engine runs and all electrical accessories can be used. START — Engages the starter. If this happens, fully return the ignition switch to the “LOCK (PUSH OFF)” position, and start the engine again.
How do I know if my ignition lock cylinder is bad?
Common signs include the car not starting, the key getting stuck in the ignition or not going in, and issues power on the vehicle.
What happens when the ignition lock cylinder goes bad?
A worn key or ignition lock may result in difficulty turning the key when it is inserted. The worn lock or key may cause the lock assembly to jam when the key is inserted, and may bind when attempting to turn the key. A worn cylinder or key may also cause the assembly to jam or stick when attempting to remove the key.
Can the ignition freeze?
Frozen ignition locks A main cause of a frozen ignition lock is moisture inside the car. If you leave wet clothes in your car overnight, or track a lot of snow in it, the inside of your car will have moisture in the air. This moisture could end up freezing your ignition lock.
What does St mean on ignition switch?
Connect starter relay wire to the “ST” terminal of the ignition switch. The “ST” terminal only activates when the ignition switch is turned to the “START” position and is a spring-loaded momentary contact.
How do I turn my key into on position?
To start, keep your foot on the brake pedal (or on the clutch if your vehicle has a manual transmission) and turn the key clockwise, away from you. When you hear the engine start, release your grip on the key. The ignition switch will then automatically turn to the ‘ON/RUN’ position for driving.
What do the numbers mean on an ignition switch?
The numbers on the ignition switch are the “standard” terminal identifying code. 30 is the incoming 12 volts from the battery. 54 is the supply to all the instruments and warning lights. 15 is the power to the ignition system (coil and distributor) 50 is the supply to the starter motor (presumably solenoid thereon)Aug 9, 2008.
Which turn signal is which?
On most cars, the turn signal lever is located to the left of the steering wheel. Shifting the lever up indicates a right turn and shifting it down indicates a left turn. Your turn signal should turn off after a turn or a lane change, but if it does not, you should turn it off manually, as soon as possible.
What is the II key position?
Key position II – With the remote control key fully inserted into the ignition switch – Give a long. press on START/STOP ENGINE.
Which is the clutch pedal?
The clutch pedal is the pedal by which the driver of a vehicle operates the clutch. In most models, the clutch pedal is on the left of the shaft, with the brake and throttle on the far right.
Does ACC mode drain your battery?
Does ACC mode drain the battery ? Yes, switching the ignition to ACC mode drains some power from the battery though not as much as when it is switched to the ON position. The power drain can increase further when the car’s radio or any other appliance plugged into the ACC outlet is switched on.
What does ACC mean on radio wire?
ACC (red), supplies +12V power to car audio and other accessories, only when the car’s ignition is switched on. Constant (yellow), also called BAT or Battery, provides permanent +12V power from battery. This allows the radio to retain settings (for example stored radio stations) when the ignition is switched off.
What is the proper way to turn off a car?
In a nutshell, the sequence of how to turn off a car will be: Park the vehicle and put the gearbox in ‘N’ mode. Engage the brake pedal. Shift the gear in ‘P’ Press the parking brake. Disengage the brake pedal. Push the stop button to shut the engine off.
What is the difference between an ignition switch and ignition lock cylinder?
The ignition lock cylinder and ignition switch are not the same thing. The lock cylinder is the mechanical tumbler your key slides into; the switch is the electrical portion that sends power to the vehicle. On many cars, these are two separate components that can be repaired individually.
What are signs of a bad ignition coil?
What Are the Signs of a Faulty Ignition Coil? Loss of Power. This is one of the first symptoms of ignition coil failure. Check Engine Light On. Poor Fuel Economy. Backfiring. Misfiring Engine. Hard Starts and Stalling. Spluttering and Coughing Sounds. Jerking and Vibrating.
Can a bad ignition lock cylinder cause no start?
Your lock cylinder connects to your ignition switch and they both work in concert to start your vehicle. If you are experiencing a ‘no start condition’, you might have a failing ignition lock cylinder. However, if your ignition lock cylinder is causing you problems, you might have to jerk your key around to remove it.
