Table of Contents
The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. These screws adjust the engine’s output at low and high speeds.
What does LA mean on Stihl chainsaw?
One marked “H”, for high speed, one marked “L”, for low speed and one marked “LA”, which is your low speed air adjustment for idle.
How do you adjust the H and L on a Stihl chainsaw?
They are the high-speed, low-speed and idle adjustments respectively. Determine the carburetor type before adjusting the high- and low-speed screws. To do this, turn the “L” screw clockwise as far as it will go, using a flat-head screwdriver, then turn it counterclockwise as far as it will go.
What does H and L mean on a chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
How do you adjust the altitude on a Stihl chainsaw?
Move the saw’s throttle level to high and then adjust the high speed screw by turning it in 1/8-turn increments to the right if the engine begins to sputter out. If the engine sounds like it is running too fast, turn the screw in 1/8-turn increments to the left until the engine runs smoothly.
Why does my Stihl chainsaw bog down?
The Job of the Carburetor Without the right amount of air and fuel in the piston cylinder, the 2-cycle engine in a Stihl chain saw runs inefficiently and the saw loses power. When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.
Why does my chainsaw bogs down at full throttle?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does a chainsaw cut crooked?
Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain. If you sharpen your chain at a 25º setting on your left hand, your right hand cutters should match.
How do you adjust a Stihl carburetor?
Turn the H screw clockwise with a carburetor adjustment tool until the head is spinning as fast as it will go, then back off the screw carefully until the RPMs start to decrease. Turn the screw slowly clockwise again until the engine once again just starts to pick up speed.
How do you adjust the carburetor on a Stihl hedge trimmer?
Turn the high speed screw (H) counterclockwise as far as stop (no more than 3/4 turn). Turn the low speed screw (L) clockwise as far as stop, then turn it back 3/4 turn. *Please note: Do not overturn the screw as this may damage the thread.
Will a Stihl chainsaw run without a fuel filter?
Well as long as the lack of that fuel filter doesn’t cause leaking at the inlet connection, then yes it will run fine …. but only for as long as whatever the filter might have caught and preventing it from clogging jets and passages.
Why does my chainsaw only runs on choke?
If your chainsaw only runs with the choke on, it is likely an issue with your carburetor. If the carburetor is plugged, the engine will be starved of fuel and will not run. However, if the engine is plugged, the choke will pull more fuel through the carburetor’s idle circuit and allow it to run.
How do I get my chainsaw to idle?
First set the idle speed by setting it as high as possible without engaging the clutch (close to 2700 RPM if you have a tachometer). Then set the low-speed screw by turning it gently in until the engine begins to starve for fuel, then turn it out gently until the engine loads up.
How do you adjust the idle on a Stihl ms250?
Adjust the low-speed and idle screws if the chain turns on its own when idling. Turn the low-speed screw clockwise until it stops, and then one turn counterclockwise. Turn the idle speed screw counterclockwise until the chain stops turning on its own, and then turn the screw one-fourth turn clockwise.
What are the 2 screws on carburetor?
There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. Often these look like flat-head screws and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.
How tight should a chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why does my Stihl chainsaw dies when I give it gas?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
