Table of Contents
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
Can you use a roller to apply Thompson’s water Seal?
All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck. You can apply some products with a garden sprayer or paint roller, but for classic deck stain, a paint pad on an extension pole is best.
What kind of brush do you use for Thompsons water Seal?
Note: If you choose an oil-based-finish, you’ll want to use natural bristled brushes or roller covers. For water-based finishes, use synthetic brushes or rollers. Some water-based finishes recommend against using a roller, so a paint pad is the best alternative.
What can I put over Thompsons water Seal?
You can only paint over Thompson’s Water Seal if you wait 45 days and use a primer. This only works if you paint over concrete, but paint doesn’t always stick to the Thompson’s seal well. Your paint may not look as intended because Thompson’s Water Seal has hydrophobic tendencies.
Is Thompson’s Water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
How many coats of Thompson Water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
How long does Thompson clear water seal last?
If applied correctly, Water Seal will last up to 4 years.
Should I use Thompson Water Seal on pressure treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
How long does it take for Thompsons Water Seal to dry?
Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompson’s® WaterSeal® Waterproofing Wood Protector – Clear.
What temperature do you apply Thompson’s Water Seal?
Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application.
Can I apply 2 coats of Thompson’s Water Seal?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
Is Thompson’s Water Seal oil based or water-based?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
Do you paint or water seal first?
Things You’ll Need Paint can be applied to water sealers, but the drying time of the sealer itself is the most important part of this task. For best results, prime the water-sealed wood first. Use either a latex-based or an oil-based primer as your first coat of paint before applying the finishing coat.
How do you remove Thompson’s water Seal?
Steps to Remove the Sealant: To use mineral spirits, wipe the spirits over the area with a cloth. Let it sit for a few minutes, then scrub the area with a scrub brush. To use a concentrated degreaser, follow the instructions on the label of your selected product.
Should you put a sealer over stain?
Applying a topcoat sealer is not required, but a finish protects the stained wood from scratches and keeps it from fading over time. If applying a polyurethane finish with a brush, apply one to two coats. If using a spray can, hold 8 to 12 inches from the surface and apply two or three light coats.
What is the best sealant for pressure treated wood?
Best Deck Sealers for Pressure-treated Wood Ready Seal 520 Exterior Stain and Sealer for Wood. SEAL-ONCE Nano+Poly Ready Mix Penetrating Wood Sealer. #1 Deck Premium Semi-Transparent Wood Stain for Decks. Thompsons Waterseal Solid Waterproofing Stain. Eco Advance Wood Siloxane Waterproofer Concentrate.
Can you use too much Thompson Water Seal?
If over-application occurs and there is puddling of the product, redistribute product within 15 minutes to a dry area or wipe off. Q: Will the formula of Thompson’s® WaterSeal® Sport Seal® or Fabric Seal change the feel of the treated surface? No. These products will not change the surface’s feel or leave it sticky.
How much does Thompson’s Water Seal Cover per gallon?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet).
How much water seal do I need?
Remember that sealers will require multiple coatings, so you’ll probably need at least two gallons for most projects. A gallon only covers so many square feet: One gallon of sealer covers 200-300 square feet. One gallon of waterproofing covers 100-200 square feet.
Is Thompson Water Seal milky white?
Thompson’s Water Seal Advanced Natural Wood Protector goes on milky but dries clear.
What is the best way to seal pressure treated wood?
For fully exposed decks, a water-repellent sealer or a penetrating semi-transparent stain may provide the best finishing solution, even on wood that has been pressure treated with preservatives. Special formulations made specifically for decks are available.
Can you use Thompson water Seal on untreated wood?
Yes. Although pressure-treated lumber is pre-treated with chemicals, preventing insect damage, it is NOT waterproofed. In fact, the chemical treatment actually causes the lumber to dry out quicker and absorb more water than untreated lumber. When wood absorbs water, it swells; as the wood dries it shrinks.
