Table of Contents
The synchronous speed of an AC motor is determined by the frequency of the source and the number of poles. The RPM is calculated by multiplying the frequency times 60 and dividing by the number of pairs of poles. Actual speed of the induction motor will be less than the synchronous speed.
What is synchronous speed?
The synchronous speed is the speed of the revolution of the magnetic field in the stator winding of the motor. It is the speed at which the electromotive force is produced by the alternating machine. The Synchronous Speed is given by the relation shown below.
What is the equation of synchronous speed ns?
Hence the magnetic flux in the stator is said to rotate at synchronous speed (Ns). For example, for a 6-pole, 50 Hz, 3-phase induction motor, Ns = 120 * 50/6 = 1000 rpm. It means that the flux rotates around the stator at a speed of 1000 rpm.
What is synchronous speed of 3-phase induction?
The 3-phase 4-pole (per phase) synchronous motor will rotate at 1800 rpm with 60 Hz power or 1500 rpm with 50 Hz power. If the coils are energized one at a time in the sequence φ-1, φ-2, φ-3, the rotor should point to the corresponding poles in turn.
What is synchronous speed and slip speed?
Thus, the speed of the rotor is always kept slightly less than the synchronous speed. The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed.
What is the use of synchronous speed?
Synchronous speed is a significant parameter for the rotating magnetic field-type AC motor. It is determined by the frequency and the number of magnetic poles.
What is slip formula?
If the revolving magnetic flux’s synchronous speed & the speed of rotor are Ns & Nr in the motor, then the speed among them can be equivalent to (Ns – Nr). So, slip can be determined as. S = (Ns – Nr) / Ns.
What is generator synchronous speed?
At synchronous speed of 1800 rpm, generator will produce no power. When the driving speed is increased to 1860 rpm (typical example), full output power is produced. If the prime mover is unable to produce enough power to fully drive the generator, speed will remain somewhere between 1800 and 1860 rpm range.
What is the difference between rotor speed and synchronous speed?
Induction motor with squirrel cage rotor has two different speeds. The synchronous speed refers to the stator rotating magnetic field, which depends on the number of poles and frequency. The other speed is the rotor’s. The rotor speed will be always slower than the stator speed, we call it slip.
What is the slip?
Slip is the differentiation between synchronous and asynchronous speed. The difference between the synchronous speed of the electric motor magnetic field, and the shaft rotating speed is slip – measured in RPM or frequency. Slip increases with increasing load – providing a greater torque.
How do you calculate synchronous speed?
The synchronous speed of an AC motor is determined by the frequency of the source and the number of poles. The RPM is calculated by multiplying the frequency times 60 and dividing by the number of pairs of poles. This was explained in Chapter 6.
What is relation between synchronous speed and frequency?
The synchronous speed of the motor depends on; Frequency of the supply source. Number of poles of the motor.Synchronous speed Formula. No. of Poles Frequency (50 Hz) Frequency(60 Hz) 2 3000 3600 4 1500 1800 6 1000 1200 8 750 900.
What is slip in 3 phase induction?
“Slip” in an AC induction motor is defined as: As the speed of the rotor drops below the stator speed, or synchronous speed, the rotation rate of the magnetic field in the rotor increases, inducing more current in the rotor’s windings and creating more torque.
Can slip be negative?
If the rotor of an induction machine rotates above synchronous speed, slip is negative, as are torque, mechanical output power and air gap power. i.e. the machine is operating as a generator. Rotational losses are 2450W.
What is full load slip?
The slip corresponding to full load speed of th motor is called full load slip. Example 1 : A 4 pole, 3 phase induction motor is supplied from Hz supply. Determine its synchronous speed. On full load, its speed is observed to be 1410 r.p.m. calculate its full load slip.
What happens when slip is zero?
Zero slip means that rotor speed is equal to synchronous speed. If rotor is rotating at synchronous speed in the direction of rotating magnetic field the, there will be no flux cutting action, no emf in the rotor conductors, no current in rotor bar conductor and hence no development of electromagnetic torque.
What is the principle of synchronous machine?
The principle of operation of a synchronous motor can be understood by considering the stator windings to be connected to a three-phase alternating-current supply. The effect of the stator current is to establish a magnetic field rotating at 120 f/p revolutions per minute for a frequency of f hertz and for p poles.
What is the principle of synchronous generator?
The principle of operation of synchronous generator is electromagnetic induction. If there exits a relative motion between the flux and conductors, then an emf is induced in the conductors.
Why the speed of synchronous motor is constant?
When you supply 60 Hz (or 50 Hz), the motor will spin at one speed, which is dependent on the number of poles. This rotational speed will be constant with different mechanical loads, up to the point that the motor (or coupling) fails, hence it is a “constant speed” motor.
What is slip frequency?
Slip frequency can be measured by determining the phase angle traversed in a defined period. For example, with a slip setting of 2 seconds (0.055 Hz) and slip frequency of 0.04 Hz, an angle of approx 29° (elec) is traversed before synchronising is permitted, as shown in Fig 12.15.
What is slip in machine?
In an electrical coupling, slip is defined simply as the difference between the speeds of the two rotating members. In an induction motor, slip is a measure of the difference between the machine’s synchronous speed and its shaft speed.
How is slip of Ship calculated?
Calculate the value of the propeller slip during this period. ( A nautical mile equals 1852 m.) Soln: Slip (percent) = Engine distance – ship’s distance/ Engine’s distance X 100. Engine distance = Pitch X RPM X 60 X 24 / 1852.
