Table of Contents
Slip in Induction Motor is the relative speed between the rotating magnetic flux and rotor expressed in terms of per unit synchronous speed. It is a dimensionless quantity. This rotating magnetic field cuts the stationary rotor conductors to generate emf.
What is the slip in induction motor?
“Slip” in an AC induction motor is defined as: As the speed of the rotor drops below the stator speed, or synchronous speed, the rotation rate of the magnetic field in the rotor increases, inducing more current in the rotor’s windings and creating more torque.
What is r2 in induction motor?
The rotor resistance R2 is constant. It is independent of slip. The reactance of the induction motor rotor depends upon the inductance of the rotor, voltage frequency, and rotor’s current. In the above equation, X20 is the standstill reactance of the rotor.
What is slip in 3 phase motor?
This speed difference is called slip. Therefore, the difference between the synchronous speed Ns of the rotating stator field and the actual rotor speed N is called slip. The slip increase with load and is necessary for torque production. Slip speed is equal to the difference between rotor speed and synchronous speed.
What is the normal slip of an induction motor?
Because of this speed difference, the motor rotates at a speed slightly slower than the synchronous speed. Slip is normally expressed in percentage. Slip of a power induction motor is 2 to 3% when the motor is operated under the rated load.
What happens if slip of induction motor is 1?
When the Value of Slip is >1 If the slip value of the motor is greater than one then the rotor will turn in the opposite direction to the revolution of magnetic flux. So if the magnetic flux is revolving in the direction of clockwise, then the rotor will turn rotating in the anti-clockwise direction.
What happens when slip is zero?
Zero slip means that rotor speed is equal to synchronous speed. If rotor is rotating at synchronous speed in the direction of rotating magnetic field the, there will be no flux cutting action, no emf in the rotor conductors, no current in rotor bar conductor and hence no development of electromagnetic torque.
What is no load test of induction motor?
The no-load test approximates the stator circuit (Rs and Xs1) and magnetization branch parameters(Xm) of an induction machine. The machine is brought to its rated speed by applying rated three phase volt- age at the stator (Vnl). Corresponding no-load current (Inl) and no-load real power input(Pnl) are recorded.
When motor is in rest What is the back EMF?
Back emf is zero when the motor is not turning, and it increases proportionally to the motor’s angular velocity. Back emf is the generator output of a motor, and so it is proportional to the motor’s angular velocity ω.
What is the function of induction motor?
An induction motor or asynchronous motor is an AC electric motor in which the electric current in the rotor needed to produce torque is obtained by electromagnetic induction from the magnetic field of the stator winding. An induction motor can therefore be made without electrical connections to the rotor.
What is slip speed?
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
What is slip percentage?
The difference between theoretically calculated forward speed based on angular speed of the rim and rolling radius, and actual speed of the vehicle, expressed as a percentage of the latter, is called ‘slip ratio’.
What is full load slip?
The slip corresponding to full load speed of th motor is called full load slip. Example 1 : A 4 pole, 3 phase induction motor is supplied from Hz supply. Determine its synchronous speed. On full load, its speed is observed to be 1410 r.p.m. calculate its full load slip.
Can slip be negative?
If the rotor of an induction machine rotates above synchronous speed, slip is negative, as are torque, mechanical output power and air gap power. i.e. the machine is operating as a generator. Rotational losses are 2450W.
Is 3 phase induction motor is self starting?
Three-phase induction motor is self-starting, because winding displacement is 120 degrees for each phase and supply also has 120 phase shift for 3-phase. It results in a unidirectional rotating magnetic field is developed in air gap which causes 3-phase induction motor to self-start.
What is synchronous speed?
Synchronous speed is a significant parameter for the rotating magnetic field-type AC motor. It is determined by the frequency and the number of magnetic poles. A collective name for the motors that run at the synchronous speed is the synchronous motor.
What is slip in machine?
In an electrical coupling, slip is defined simply as the difference between the speeds of the two rotating members. In an induction motor, slip is a measure of the difference between the machine’s synchronous speed and its shaft speed.
What are types of induction motor?
Types of Induction Motors Split Phase Induction Motor. Capacitor Start Induction Motor. Capacitor Start and Capacitor Run Induction Motor. Shaded Pole Induction Motor.
What are the main parts of 3 phase induction motor?
The stator of the three-phase induction motor consists of three main parts : Stator frame, Stator core, Stator winding or field winding.
Why slip ring is used in motor?
A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals.
When slip is zero rotor will?
If Slip is equal to zero, rotor current is zero and torque is zero. The zero torque means motor will not rotate at all.
What is motor slip formula?
Slip speed is the speed difference between the Synchronous speed and Rotor speed. Slip speed = Synchronous speed – Rotor speed = Ns -N. Slip, s = (Ns – N) / Ns.
What is load test of induction motor?
The load test on induction motor is performed to compute its complete performance i.e. torque, slip, efficiency, power factor etc.
Why is it called induction motor?
This type of engine is also known as an induction motor. The asynchronous motor is based on the currents induced in the rotor from the rotating magnetic field of the stator. That’s why it’s called an induction machine.
What happens if fifth harmonics is given to induction motor?
It will rotates in normal operation. Either short circuit or open circuit occurs. The sinusoidal components having frequency five times of fundamental are known as fifth harmonics. Hence induction motor will rotates in reverse direction because of reverse phase sequence of fifth harmonics.
