Table of Contents
“Slip” in an AC induction motor is defined as: As the speed of the rotor drops below the stator speed, or synchronous speed, the rotation rate of the magnetic field in the rotor increases, inducing more current in the rotor’s windings and creating more torque. Slip is required to produce torque.
What is the slip?
A slip is a woman’s undergarment worn beneath a dress or skirt. A full slip hangs from the shoulders, usually by means of narrow straps, and extends from the breast to the fashionable skirt length. A half slip (or waist slip) hangs from the waist.
What is slip in induction motor formula?
Slip speed is the speed difference between the Synchronous speed and Rotor speed. Slip speed = Synchronous speed – Rotor speed = Ns -N. Slip, s = (Ns – N) / Ns.
Why it is called slip test?
The method used to determine Xq and Xd, the direct and quadrature axis reactance is called slip test. Current induced in the damper winding of alternator will produce an appreciable error. Induced voltage in the open circuit field may reach dangerous values.
What is slip slip test?
Slip test is performed on salient pole synchronous machine to determine the direct axisreactance and quadrature axis reactance.As in a salient pole synchronous machine , air gap is not constant ; like in cylindrical rotortype rotor ; reactance around quadrature axis (Xq) is different from reactance along directaxis (Xd
What is full load slip?
At full load the speed of the motor is 1350 rpm. Hence slip at full load = 5.33% When the motor is so loaded that the rotor speed is reduced to 0, the value of Slip is 1. Hence, value of Slip gradually increases from no-load to full load.
What is 120 in motor speed formula?
Frequency of synchronous machine in cycles per second or Hertz is same as speed of rotor in revolution per second. Hence, frequency of voltage wave f =p÷2 x n÷60 , here n=mechanical speed in rpm , p=total No of poles, thus p÷2=pairs of poles and 120 = 60×2 in above formula.
What is the value of slip at starting?
Slip in Induction Motor is the relative speed between the rotating magnetic flux and rotor expressed in terms of per unit synchronous speed. It is a dimensionless quantity. The value of slip in induction motor is can never be zero.
What is the motor slip?
Slip is the differentiation between synchronous and asynchronous speed. The difference between the synchronous speed of the electric motor magnetic field, and the shaft rotating speed is slip – measured in RPM or frequency. Slip increases with increasing load – providing a greater torque.
Why must slip be present for Motor Action?
Because of the above phenomenon, the rotor speed “N” is always less than the synchronous speed “Ns” which keeps the motor moving. This difference between synchronous speed of the rotating magnetic field and synchronous speed is known as slip. Hence slip is an essential feature for proper working of the induction motor.
What is normal slip of an induction motor?
Because of this speed difference, the motor rotates at a speed slightly slower than the synchronous speed. Slip is normally expressed in percentage. Slip of a power induction motor is 2 to 3% when the motor is operated under the rated load.
What is Torque slip?
The torque slip curve for an induction motor gives us the information about the variation of torque with the slip. The slip is defined as the ratio of difference of synchronous speed and actual rotor speed to the synchronous speed of the machine.
What does negative slip mean?
Negative slip indicates that the motor is running above synchronous speed. This can happen only when it is driven by a prime mover. This motor becomes an induction generator.
What is slip and its significance?
Importance of Slip in Induction Motor. In the induction motor rotor always rotates speed less than synchronous speed. The difference between the rotor speed (N) and the rotating magnetic flux speed (Ns) is called slip.
When can only slip of an induction motor is zero?
In motors the number of rotor slots and stator slots are different and thus cogging (magnetic locking) can’t happen. And thus The slip motor can’t run at rated speed. Torque developed by induction motor is proportional to the slip. At synchronous speed,slip is zero and hence torque developed by the motor is zero.
At what speed slip test is conducted?
The machine is run at a speed a little less than the synchronous speed (the slip being less than 1%) using a prime mover (or motor). Connection diagram is shown in circuit diagram.
What is slip in 3 phase induction?
Slip in Induction Motor is the relative speed between the rotating magnetic flux and rotor expressed in terms of per unit synchronous speed. It is a dimensionless quantity. The value of slip in induction motor is can never be zero.
What happens if slip of induction motor is 1?
When the Value of Slip is >1 If the slip value of the motor is greater than one then the rotor will turn in the opposite direction to the revolution of magnetic flux. So if the magnetic flux is revolving in the direction of clockwise, then the rotor will turn rotating in the anti-clockwise direction.
How is slip of a motor calculated?
The multiplication of 100 and speed difference divided by the synchronous speed is known as slip of an induction motor. It’s always represented in percentage, generally it ranges from 0.4% to 6% based on its design factors.
How do you do a slip test?
Variable-angle ramp The angle at which the subject slips is then recorded. Two operators repeat this test three times and then an average is calculated. The repeatability of this test method was extensively documented. Tests can be performed dry, wet with soapy water and bare feet, wet with oil, etc.
What is slip and slip speed in induction motor?
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
What will happen when the slip is 100 and zero?
What will happen when the slip is 100 and zero? As the rotor ends are short circuited current flows through the rotor. So when slip is zero there is no phase difference between stator flux and rotor flux and there is no torque exerted on rotor and rotor does not rotate .
