Table of Contents
RH: The RH terminal is the 24-volt heating power supply. Y/O: The Y/O terminal is used to control the cooling condenser. When the thermostat calls for cooling, signals are sent to power up the condenser and the blower fan, cooling your home. W/B: The W/B terminal controls the heat relay or valve.
What does RH stand for in thermostat?
Rh stands for Red-Heat and Rc stands for Red-Cool. If you only have a single red wire the jumper between Rh and Rc are required for some heating and cooling hybrid systems depending on your thermostat. Yellow/Y is the AC compressor.
Is Rh the same as R on thermostat?
R , Rh , and Rc are all the same, but not. In general terms, the R terminal is where you connect the signal voltage source. In low voltage controlled systems, there will be a step down transformer that provides the power to the control circuitry.
Do I use RH or RC on thermostat?
RH is for the heating unit and RC is for the A/C unit. There will usually be two thermostat cables – don’t mix them up. If the air conditioning thermostat has one transformer to power both the heating and cooling system, then the wire from the transformer goes directly to the RC terminal and is called the RC wire.
Does R wire go to RC or RH?
Here are some general guidelines: An R wire can go into a Nest Learning Thermostat’s Rc or Rh connector. The Nest Thermostat E only has an R connector, which is typically where an R wire would go. These are not jumper wires, and you can insert the Rc wire into the Rc connector and the Rh wire into the Rh connector.
Should RC and RH be connected?
If you have both an Rh (Red-heat for powering the heating) and an Rc (Red-cool for powering the cooling), then the R wire can be connected to either Rh or Rc. If you only have a single R wire, then it will only have an R connector, which is the connection you’ll use.
What is the Rh wire on the Nest thermostat?
What is the Rh wire on the Nest thermostat? The Rh wire is the power input to the heating system of your air conditioning. If the connection is not established, your air conditioning will stop working.
Do I need a jumper from R to RC?
If you have a wire in the R terminal, and no wire in the RC terminal, use the jumper selector switch, the jumper plug, or a small jumper wire to connect the R and Rc terminals. If you have a wire in the R terminal, and another wire (not a jumper) in the RC terminal, you will not need to connect the R and RC terminals.
What is RC and RH on ecobee?
With dual-transformer systems you’ll have two R wires—one from the cooling transformer (Rc) and one from the heating transformer (Rh). Learn how to install an ecobee thermostat in a dual-transformer system. Rc. If you don’t have an Rh wire, Rc serves as both the cooling and heating power wire.
What color is Rh wire?
Red Marking Wire Color Code Description Rh Red Power from heat, 24 Vac transformer C Black/Blue Common of 24 Vac transformer W White Primary heat cell relay E Brown Emergency heat relay.
Where does RC and RH wire go on nest?
Use the wiring diagram you got from the compatibility checker in step 4 to connect your system wires to the Nest Thermostat. Note: If you have an R, Rc or Rh wire, you can put it into the R connector on the Nest Thermostat. If you have a W2, Y2 or O/B wire, you can put it into the *O/B connector, if needed.
What is RC RH jumper?
“Rh”(R-Heating)&”Rc”(R-Cooling) are used separately if you have separate heating system and separate cooling system on one thermostat. The jumper on your thermostat combines them together since you have 1 hvac system that does heating & cooling.
What is the Rh wire for?
The Rh wire connects to your heating system as opposed to your cooling system. This wire may be red without an H attached to it, depending on if you have a dual transformer setup. The Rh wire connects to the RH terminal on your thermostat.
What is OB wire on thermostat?
The wires are used to switch the changeover valve in a heat pump system. The O and B wires switch the valve from cooling to heating.
What happens if you wire a thermostat wrong?
Potential consequences of improper installation could include: Electric shock. Blowing a circuit breaker. Damaging the thermostat unit, the electrical system or even the AC/furnace unit itself.
How do I know if I have 2 stage cooling?
We think the best way to determine whether you have multistage heating or cooling is to pop your current thermostat off its base and take a look at its wires. Once you’ve popped your current thermostat off its base, look at the wires leading into the terminals, particularly the W, W1, Y, and Y1 terminals.
Where does the black wire go on a Honeywell thermostat?
More often than not, the black or blue wire connected to the C terminal is found in the newer “smart” thermostats. The older thermostats may not have the “C” wire; they function on-demand while the new ones function all the time (continuously 24/7).
What is the OB switch on thermostat?
The O/B terminal is for heat pump systems and is used for the reversing valve. When the “O” option/position is selected the reversing valve defaults to the heating mode. If the “B” option/position is selected the reversing valve defaults to the cooling mode.
What is dual transformer system?
If you have a boiler as well as an air conditioner, you have a dual transformer system. With dual transformer setups, you will have two R wires—one from the cooling transformer (RC) and one from the heating transformer (RH).
