Table of Contents
In a thermostat, the R wire is responsible for powering the entire HVAC system (through a transformer). If you have both an Rh (Red-heat for powering the heating) and an Rc (Red-cool for powering the cooling), then the R wire can be connected to either Rh or Rc.
Do I need a jumper from R to RC?
If you have a wire in the R terminal, and no wire in the RC terminal, use the jumper selector switch, the jumper plug, or a small jumper wire to connect the R and Rc terminals. If you have a wire in the R terminal, and another wire (not a jumper) in the RC terminal, you will not need to connect the R and RC terminals.
Does R go to RC or RH?
Here are some general guidelines: An R wire can go into a Nest Learning Thermostat’s Rc or Rh connector. The Nest Thermostat E only has an R connector, which is typically where an R wire would go. These are not jumper wires, and you can insert the Rc wire into the Rc connector and the Rh wire into the Rh connector.
What does R and W mean on thermostat?
W wire – heat. R wire – heat power. W wire – heat.
What is R and RC?
RC is no different and simply means red cooling. The wire is generally red, although there is no color standardization — but more importantly, the “R” really means that the wire and terminal are hot; it’s a live electrical wire. The RC wire connects to the RC terminal, which controls the cooling system.
Why does my thermostat have R and RC?
In a thermostat, the R wire is responsible for powering the entire HVAC system (through a transformer). If you have both an Rh (Red-heat for powering the heating) and an Rc (Red-cool for powering the cooling), then the R wire can be connected to either Rh or Rc.
Where does red wire go on thermostat?
RED WIRE. The red wire should be connected with the Thermostat RH terminal. You can also connect it to the RC terminal with a jumper wire between the RH and the RC. If you only have one R terminal for both heating and cooling, connect it to that.
Should I use RH or RC?
RH is for the heating unit and RC is for the A/C unit. There will usually be two thermostat cables – don’t mix them up. If the air conditioning thermostat has one transformer to power both the heating and cooling system, then the wire from the transformer goes directly to the RC terminal and is called the RC wire.
What is the Rh wire?
The Rh wire connects to your heating system as opposed to your cooling system. This wire may be red without an H attached to it, depending on if you have a dual transformer setup. The Rh wire connects to the RH terminal on your thermostat.
What is Rh vs RC on thermostat?
RC: The RC terminal is the 24-volt cooling power supply. RH: The RH terminal is the 24-volt heating power supply. (Note: The RC and RH terminals are jumpered together in a four-wire heat/cool system and a single-stage heat pump system, but not in a five-wire heating/cooling system.)Jun 8, 2021.
What do the letters mean on thermostat wiring?
W, W1, W2: Just like the Y wire, the W wire(s) control the heating aspect of your system. O, B, O/B: These wires are responsible for switching the changeover valve in a heat pump system. The O wire reverses the valve from heating to cooling, and the B wire switches the valve from cooling to heating.
How do you read a thermostat?
Tape the paper towel to the wall next to your thermostat and then tape the thermometer directly to the paper towel. Leave the thermometer in place for 15 minutes and then check both temperatures afterwards. With the thermometer next to the thermostat, you’ll be able to read the same temperatures your thermostat reads.
What does R and C mean on a transformer?
In the case of HVAC/R systems, the power source is a low-voltage transformer (usually a 24 VAC transformer) and the two wires supplying the power are labeled C (common) and R. For systems that do not have access to the C wire, a battery in the thermostat compartment must be used.
What’s the blue wire on a thermostat?
Blue wires are also called “C” wires because they are the Common wire. C wires are necessary for any “smart” thermostat that needs to be connected to a power source 24/7, regardless of your heat pump type.
Which wire is which thermostat?
Thermostat Wiring Tips If your thermostat controls your heat, you will have a white wire. The Y wire is yellow and connects to your air conditioning compressor. The G wire is green and connects to the fan. Rc and Rh: The red wire(s) are the power source for your thermostat.
What is RC and RH?
Rh stands for Red-Heat and Rc stands for Red-Cool. If you only have a single red wire the jumper between Rh and Rc are required for some heating and cooling hybrid systems depending on your thermostat. Yellow/Y is the AC compressor. White/W is the Heating element. Green/G runs the fan.
