Table of Contents
WHAT IS STABILIZER? Outdoor chlorinated pools require stabilizer (cyanuric acid) to protect the chlorine from being burnt off by UV rays from the sun. The ideal level of stabilizer is between 30 and 70 ppm. Salt water pools should be kept between 50 – 70 ppm.
Is pool stabilizer necessary?
Pool stabilizers are important to maintain a clean swimming pool. Along with other factors for keeping a swimming pool clean, like pH, total alkalinity, and water hardness, pool stabilizers need to be adequately regulated and tested.
When should I add stabilizer to my pool?
The product is typically added to the pool when it is first opened for the summer season. Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer.
Is pool stabilizer the same as shock?
Pool stabilizer is also known as pool conditioner, chlorine pool stabilizer, chlorine stabilizer, or Cyanuric Acid. It’s also included in chlorine tablets or sticks (called trichlor) or shock (called dichlor). When they’re mixed together in shock or tablets, the resulting product is called stabilized chlorine.
Is pool stabilizer the same as baking soda?
Baking soda is used to raise the total alkalinity of the pool. It isn’t a stabilizer.
Can you swim with stabilizer in the pool?
You may swim immediately if Stabilizer was added through the skimmer, otherwise wait 12 hours to swim until all product in the pool is dissolved. For pools with bleachable surfaces, such as colored plaster or vinyl, do not allow product to sit on the bottom of the pool.
Is muriatic acid a pool stabilizer?
Muriatic acid is used to lower the alkalinity and pH of your pool whereas cyanuric acid is used to stabilize the chlorine and will not noticeably lower pH. Muriatic acid can also be used for cleaning grout, stains and it’s also great for cleaning gummed up pool filters.
Can you add stabilizer and chlorine at the same time?
It Should Not Be Done Together. While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless.
Does pool stabilizer dissolve?
Pool stabilizer is quite slow to dissolve no matter what method you use. It will take 2-5 days to dissolve fully. There are two methods you can use to dissolve stabilizer into your pool water.
What happens if you put too much stabilizer in a pool?
Too much stabilizer can begin to lock the chlorine in your pool (chlorine lock) and render it useless. There is no exact level of stabilizer that guarantees chlorine lock. Chlorine lock symptoms are the same signs as a pool with no chlorine such as cloudy and/or green water and/or a strong chlorine smell.
Does stabilizer damage pool liner?
Stabilizer, or cyanuric acid, is a _very_ weak acid, it can takes a few days to completely dissolve in pool water, it will not however ruin or damage your liner.
How long after stabilizer can I shock?
8) How long after adding chemicals can I swim? Alkalinity Balance, pH up, pH down, Calcium Balance, Water Stabilizer, and clarifier are all swim-safe chemicals. Wait about 20 minutes, and you are free to swim. We suggest adding algaecide, Super Erace, and shock at night, after everyone is out of the pool.
Is there chlorine in stabilizer?
Pool stabilizers are sold in liquid and granule form. They are also even sold mixed in with chlorine tablets, sticks, and chlorine shock. These combination products are known as Stabilized Chlorine because the stabilizer is mixed in with the sanitizer.
What do you put in your pool if your stabilizer is low?
Stabilizer – if it is too low, you add cyanuric acid. If it is too high, the best option is a partial drain and refill with fresh water, but that may not be necessary depending on how high it is.
Do I need stabilizer in a saltwater pool?
Because saltwater pools don’t have the chemical chlorine, a stabilizer isn’t required. Salt Pool Facts: Salt pools are still sanitized using chlorine. A salt chlorine generator turns salt into chlorine to sanitize the pool water.
Is cyanuric acid the same as stabilizer?
In the pool industry, Cyanuric Acid is known as chlorine stabilizer or pool conditioner. Cyanuric Acid (CYA) is a pool balancing product used to help chlorine last longer.
Does chlorine increase pH?
Using liquid chlorine raises the pH of the water. Liquid chlorine does not raise pH. When added to water, liquid chlorine (which has a pH of 13) makes HOCl (hypochlorous acid – the killing form of chlorine) and NaOH (sodium hydroxide), which raises pH. So the net effect on pH is zero (or almost zero).
What happens if you put too much muriatic acid in pool?
If you do add too much muriatic acid, your pH levels can dip dangerously low, and your pool water can cause rashes and eye irritation. Low levels of pH can also damage metals in your pool like ladders, railings, screws, bolts, and other important equipment.
What do you do when pool cyanuric acid is high?
How to Lower Cyanuric Acid in Your Pool Step 1) Drain some of the pool water (to waste). Step 2) Top the pool back up to normal levels. Step 3) Run your pump for a few hours to circulate the water and mix the fresh water in with the existing water. Step 4) Retest the cyanuric acid / pool stabilizer levels again.
What happens when you mix chlorine and muriatic acid?
Mixing bleach, or sodium hypochlorite(NaClO) with muriatic acid(HCl) will liberate chlorine gas, which is definitely toxic, and a severe irritant to eyes and nasal passages and the lungs even in small amounts.
