Table of Contents
Fascia Boards are often made from a wide range of different materials, each posing various advantages and challenges. The most common materials include wood, PVC, fiber cement, aluminum, and vinyl fascia. Wood: Wood is perhaps the most common selection when it comes to designing a fascia board.
What wood is used for fascia boards?
Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.
What is wood fascia made of?
Wood fascias are the most common fascia board material. These are usually made of cedar, redwood, pine, spruce, or fir. You can also choose to prime and paint them to match the characteristics of your house. Wood fascia is beautiful and offers a natural look to the house.
What is fascia made of on a house?
Fascia is normally made of timber or wood, but can be found in PVC, aluminum, and vinyl as well. It’s typically installed at the same time as your roof or gutters in order to help complete this area of the home. Some homes may not use a fascia board.
What are plastic fascia boards made of?
Recycled plastic fascia boards and external recycled plastic cladding products from Kedel are made from a mixture of waste plastic products such as polystyrene, contact lenses and CD cases that when extruded into plastic planks and beams, create an impervious product that is low-carbon, maintenance-free and entirely.
Can plywood be used as fascia board?
Even though plywood siding isn’t a good fascia material, it works well for soffits, which are out of the rain and have to be painted and cut to install light fixtures and vents.
What is the best material to use for fascia board?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
What material is soffit and fascia made of?
While soffits and fascia are traditionally constructed from materials like aluminum and wood, many homeowners are now choosing ones made from synthetic and composite materials like UPVC and vinyl because they offer easy maintenance and durability.
How thick is a fascia board?
Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction.
What material is used for soffits?
Although unsanded and touch-sanded grades of plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
What is the difference between a fascia board and a soffit?
Fascia is installed around the entire structure and is attached to the uncovered ends of rafters or to the top of exterior walls. Soffit is designed to be installed from the exterior wall to the fascia board. Sometimes the roof is flush with the edge of the exterior walls.
Are fascia boards structural?
The fascia board is the one inch thick board that is nailed to the lower ends of the rafters, roof joists, or trusses to close the eave (Figure FB-1). Technically it is not considered a structural member, but it provides structural support for the gutters, when they are nailed to it.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
How long does plastic fascia boards last?
While they tend to last for years, fascia and soffits do need replacing, so every homeowner eventually needs to recognise the signs of wear and tear.
What is the board behind the fascia called?
Soffit is the layer of wood, vinyl or aluminum that extends from the bottom of the fascia to the top piece of your wall board. Together, they protect the rafters from weather, moisture, and allow air to flow through soffits and vents.
Can you use plywood for soffit?
plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
Can I use pressure treated wood for fascia?
It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.
What kind of nails do you use for fascia?
You must use exterior grade nails. A finishing nail, which has a smaller head and can be countersunk, will give a clean look but nails with a head will be more secure. You can hammer it farther into the wood and cover with putty, caulk or wood epoxy before you paint.
Can I use 2×4 for fascia board?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
Can PVC be used for fascia board?
Obviously the biggest reason for using a PVC trim board is long term maintenance combined with traditional architectural appeal. PVC trim boards will not rot, twist, split or warp. In addition you can leave it unpainted if you like or paint it to match a certain color scheme.
How much does it cost to replace fascia boards?
1. Average Cost to Replace Fascia and Soffit Cost Per Linear Foot Total Cost* Low Cost $6 $1,500 Average Cost $10 $2,500 High Cost $20 $5,000.
