Table of Contents
What is the purpose of an ejector pump?
The ejector pump is connected to a storm drain or dispersal device to deliver water away from your home. This water is then processed and the lid of the ejector pump will be sealed to prevent any harmful chemicals or gases from entering your home.
What’s the difference between a sump pump and an ejector pump?
While the sump pump manages groundwater, the ejector pump moves wastewater from basement toilets and greywater from basement sinks, appliances, and floor drains uphill to the main sewer line. The ejector pump basin should be covered with a sealed lid.
What happens if ejector pump fails?
Since gravity alone can’t remove the waste from the home, what happens if that crucial step – the ejector pump – one day fails? If that occurs, flushed water and waste can build up in the pipes and eventually burst – usually at their lowest point, which for most homes is the basement.
What is the cost of an ejector pump?
How Much Does a Sewage Ejector Pump Cost? Expect to pay between $300 and $800 for a sewage ejector pump. You’ll also need to hire a local plumber for installation. Plumbers generally charge by the hour, and the cost to hire a plumber per hour varies between $45 and $200.
Do you need an ejector pump for a basement bathroom?
If this includes a bathroom, a correct plumbing installation must be taken into consideration. An ejector pump must be installed by a professional to ensure your basement plumbing fixtures function properly. If it includes a laundry room or bathroom, contact AAA Service at (303) 622-3449.
Can I turn off ejector pump?
These pumps operate in a very harsh environment (submersed in sewage) and often fail after just a few years. Failure of your pump could mean sewage back-up in your basement. Assuming you’re home when this occurs, you should have ample time to shut-off your water before the sewage reaches flood level.
How long does an ejector pump last?
A good sewage ejector pump should last at least 7-10 years. However, with proper installation and routine care, your pump can last 30 years or more. A common reason people need to replace their sewage ejector pumps is due to faulty installation where plumbers cut corners or used the wrong sized pumps.
Why does my ejector pump smell?
During dry periods, water in the sump pit evaporates over time because the pump does not remove it. When the basin fully dries, gases escape which cause bad smells in your home.
What kind of pump do I need for a basement bathroom?
The most common application for sewage pumps is the installation of a bathroom in the basement. Because the basement is below-grade and usually situated below the sewage line entrance (usually about 4 feet below the house), a sewage pump is needed to pump waste and water up and out of the house.
How do you know if your ejector pump is broken?
If your sewer ejector pump is making strange new sounds, like grinding or screeching, or if it making its usual operational sounds but at a much louder volume than usual, don’t write them off. This is one of the first signs of trouble that you’re likely to recognize.
How often should you change your ejector pump?
You’ll likely need to change your sewage ejector pump every seven to 10 years, but if you maintain it properly and have it inspected annually, it may last up to 20 years.
How do you maintain an ejector pump?
How to Maintain Your Ejector Pump: Clean and prepare the pump. Turn off the circuit breaker and water source to the pump so it doesn’t turn on while you are working. Check the oil. Inspect pump impeller. Tighten connecting elements. Assess bearing damage. Ensure your seals remain tight. Clean your vents.
How does plumbing work in a basement?
The plumbing lines run upward through the wall to the basement ceiling and connect to the sewer or septic tank line there. This is one of the simplest options for adding a bathroom to basement areas. Some of these models include a macerating function that grinds waste down to prevent clogging.
How do you put a bathroom in a basement without breaking concrete?
The best way to install the shower in a basement bathroom without damaging your floors is to look into an upflush toilet system. While traditional basement showers require you to drill into shower base and concrete to add a drain, a Saniflo system sits on top of concrete floors.
How do you put a toilet in a basement without breaking concrete?
The best way to install a basement toilet without damaging the basement floor is to look at a toilet with a high water level. While traditional basement showers require drilling concrete to add drainage, the Saniflo system is installed on upper concrete floors.
Do you need a special toilet for the basement?
A basement toilet is a necessary addition to your basement bathroom, but plumbing a basement toilet is a different animal. If your home has the sewer-line that runs deep enough for gravity (below the basement concrete floor level) to take care of waste disposal, then you may be in luck.
Why is my ejector pump humming?
Impeller. The humming sound may be the result of a jammed impeller, the mechanical part that draws in water. Generally, debris is clogging the impeller, causing the jam and the resulting noise. To avoid this problem in the future, install a filter in the sump pump to collect debris.
