Table of Contents
What is the purpose of a trimmer stud?
A trimmer or trimmer stud is a component of a framed structure that provides additional support for an opening such as a door or window.
What is a trimmer stud in framing?
In a wood-framed rough opening, the stud or framing member which runs vertically from the subfloor to and supporting the structural header member, into which a door frame is fastened.
Where is the trimmer stud?
Trimmer: A less than full-length 2 x 4 stud that sits inside a King Stud at a rough-opening for a window or door and is the primary structural support for a Header near the top of the rough-opening.
What is the difference between Jack stud and trimmer?
Jack and king studs The header fits between two king studs and is supported by one or more jack studs at each side of a rough opening. Jacks, sometimes called trimmers, are studs cut to length to fit under each end of a header and down to the bottom plate.
What supports a trimmer stud?
The header is supported by a jack stud at each end. Jacks, sometimes called trimmers, fit under each end of a header, and they transfer the load that the header carries down to the bottom plate and the framing beneath. Jacks can be replaced with a steel header hanger attached to the king stud.
What is Clipper trimmer?
A clipper is intended for bulk hair cutting on larger areas, but does not cut extremely close to the skin. On the other hand, a trimmer is designed for edging, outlining, dry shaving and light shaping on smaller areas such as the back of the neck, around the ears, around sideburns etc.
What is another name for a trimmer stud?
The jack stud is sometimes called a trimmer stud. The term “jack” derives from mid–16th century England, where it referred to a lad, knave, or common man: Jack: (1) A man of the common people, a lad, fellow, chap, especially a low-bred or ill-mannered fellow, a knave.
What is the difference between trimmer and header?
As nouns the difference between header and trimmer is that header is the upper portion of a page (or other) layout while trimmer is one who trims, arranges, fits, or ornaments.
What does it mean trimmer?
Definition of trimmer 1a(1) : one that trims articles. (2) : one that stows coal or freight on a ship so as to distribute the weight properly. b : an instrument or machine with which trimming is done.
How far apart are studs?
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
What are the two general types of dormers?
Types Of Dormers Gabled Dormers. Gabled dormers are the most common type of dormer. Shed Dormers. Shed dormers are the simplest style of dormer. Hipped Dormers. Hipped dormers are similar to gabled dormers in that they have a peaked roof. Eyebrow Dormers. Segmental Dormers.
What is the bottom 2×4 of a wall called?
A horizontal piece at the bottom of the wall is called the bottom plate. The studs are nailed to this plate, which is nailed to the floor. At the top of the wall is the top plate. Often a doubled 2×4, it anchors the top ends of the studs as well as ties the wall into the ceiling.
What is a sill trimmer?
Sill trimmer Horizontal member immediately under a window opening, providing fixing for bottom jack studs.
Whats the difference between a king stud and a jack stud?
What are king studs? King studs run floor-to-ceiling, adjacent to and beyond the length of the jack stud, rather than supporting the header like a jack stud. They act more like a traditional wall stud, but usually fall out of the 16- to 24-inch spacing of normal studs.
What’s the difference between a king stud and a jack stud?
A king stud is one that runs continuously from the top plate to the bottom plate. The jack stud is nailed to the king stud, but it’s shorter as it supports the structural header or the flat 2x material that you use for a door in a non-load-bearing wall.
What are trimmer bars?
RE: Trimmer Bars In the UK Trimmer Bars is the name for additional bars placed round an opening, such as pipe penetrations through an RC tank wall or a large opening. They are usually placed at 45 degrees across corners (assuming horz bars at 0 deg and vert bars at 90 deg).
What is a common stud?
Common studs are vertical members which transfer loads vertically to bottom plates. They are usually evenly spaced to suit loads, lining and cladding fixing. Spacings are generally 450 or 600 mm, depending on the roof cladding. Common studs should be reinforced at points of concentrated loads.
Can I use a trimmer as a clipper?
Trimmer is used to trimming short hair. They are made up of thin blades. If your hair is already short, then you can use a trimmer instead of a clipper.
