Table of Contents
What is the difference between a line wrench and regular wrench?
A standard box wrench cannot be used on a brake line because it has a closed end. Brake line wrenches, on the other hand, engage five of the six faces of the nut, allowing just enough of an opening to let the line slide through.
What are the other names for a line wrench?
Types American name British/Commonwealth name Group flare-nut wrench tube wrench line wrench flare spanner flare nut spanner brake spanner crow’s-foot spanner common ratcheting box wrench ratcheting ring spanner common flex-head socket wrench Saltus wrench swivel head spanner common.
What is the advantage of a flare nut wrench?
Flare-nut wrenches are advantageous because they have more powerful gripping powers. It’s 5-sided design makes it much more snug around different nuts. As a result, it is better at loosening or tightening nuts than the regular wrench. Flare-nut wrenches also tend to have shorter handles.
Why do you need a line wrench?
A Very Useful Mechanics Tool If you are working with any type of fitting that is in-line – such as a brake line, fuel line, or any type of cable – a line wrench can be a life saver. Standard open end wrenches may not grip the hex well enough, which can lead to stripping – a real pain in the neck!Mar 22, 2017.
What is a tubing wrench used for?
Most often, pipe wrenches are used on threaded pipe, usually galvanized steel, black iron or similar metal pipes. A pipe wrench has two serrated jaws that are tightened and dig into the pipe for grip. The top serrated jaw adjusts up and down to fit different size pipes.
What is a flared spanner?
A flare nut spanner (also known as a ‘brake spanner’ or ‘crow’s-foot spanner’) is a simple, single-piece tool. Plumbing fasteners are often made from soft metals, such as copper, so flare nut spanners have thick jaws to maximise the contact the head has with the fastener head, preventing damage to the fastener.
Why are wrenches offset 15 degrees?
In short, having the offset angle allows you to use the wrench in confined spaces as well as on flat surfaces. However, offsetting it at a 15 degree angle reduces that swing to 30 degrees which makes your work faster and easier.
What is a crows foot wrench?
Crowfoot wrenches (also known as tight clearance offset sockets or crowfoot socket wrenches) are open-end type wrenches without a handle or shaft. Wrenches can access fasteners from the top and side and in tight spaces where a regular open-end wrench can’t reach.
What does a flare nut wrench look like?
Flare nut wrenches are a type of open-ended wrench that’s intended for use with hexagonal nuts and fittings, which are sometimes referred to as flare fittings. Visually, they resemble box or ratchet wrenches but with an open head instead of a closed loop.
Why should a wrench always be pulled rather than pushed?
Always pull, rather than push, a wrench for greater control and balance. That way, if the nut or bolt should suddenly loosen, you’re less likely to go flying. Never try to get more torque from a wrench by using a cheater bar or other device to extend the leverage.
What is the difference between an open end and a box end wrench?
They come either separately or in a combination form, with one end being an open wrench, while the other is boxed. The box end has a tendency to slip off, while the open end allows more versatility since it needs only to contact two sides of the nut or bolt.
Why use a 6 point wrench when a 12 point is available?
The number of angles in 6 point sockets is less than 12 point sockets. Therefore it allows them to have more contact inside the socket. Six-point sockets also can carry higher pressure than 12 point sockets. This is another reason to use 6 point sockets over the other one.
What type of flare is best for brake lines?
All brake lines need to be double flared, due to the high hydraulic pressure. If your brakes leak or the hoses crack, it could prove to be fatal. Single flared lines are suitable for low-pressure lines in other applications, but not your vehicle’s brakes.
What is flare nut?
During assembly, a flare nut is used to secure the flared tubing’s tapered end to the also tapered fitting, producing a pressure-resistant, leak-tight seal. Flared connections offer a high degree of long-term reliability and for this reason are often used in mission-critical and inaccessible locations.
What type of sockets are the most commonly used?
Hex sockets are the most common type of socket and come in two main types: hex/6 point sockets and bi-hex/12 point sockets.
What do torque wrenches do?
What is a torque wrench ? Used in car garages or in industry, a torque wrench is used to check and adjust the tightening torque of bolts, screws and nuts. A torque wrench is a precision tool which guarantees reliable and quality tightening.
Which pipe wrench is best?
Top 7 Best Pipe Wrench Reviews #1 Tradespro 830914 14-Inch Heavy Duty Pipe Wrench. #2 RIDGID 31100 Model 818 18-in Aluminum Straight Pipe Wrench. #3 Ridgid 31000 6″ Pipe Wrench. #4 Crescent 9″ Automotive Wrench. #5 MAXPOWER 2-Piece Heavy Duty Wide Open Adjustable Wrench Set.
Is a socket wrench a pipe wrench?
Another type of wrench often used on pipes, the plumber wrench, is also called a pipe wrench in some places. The Stillson wrench is an adjustable wrench (spanner) with hardened serrated teeth on its jaws.Pipe wrench. A modern pipe wrench Classification hand tool Related wrench, plumber wrench, monkey wrench.
