Table of Contents
GPM means Gallons Per Minute. Also known as “flow rate”, GPM is a measure of how many gallons of water flow out of your shower head each minute. Since 1992, a maximum of 2.5 GPM is the federally mandated flow rate for new shower heads. This means no more than 2.5 gallons of water should flow out each minute.
Is higher GPM better for shower head?
One person who showers 10 minutes per day with a 2.5 GPM shower head uses 9,125 gallons of water per year. Switching to a 2.0 GPM shower head saves more than 1,825 gallons of water and $25 per year in water and energy costs. Those numbers jump to 7,300 gallons and $100 in savings for a family of four.
Is 1.5 gpm shower head enough?
If you’re looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. That’s 40% less water output than the 2.5 GPM Flow Rate. That said, you don’t have to be mandated by a state to use a Shower Head with a 2.0 or 1.5 GPM Flow Rate.
Is 2.5 gpm shower head good?
Standard shower heads use 2.5 gpm, but to earn the WaterSense label, a product must use no more than 2 gpm and still meet strict performance requirements. The EPA estimates that the average family could save 2,900 gallons of water per year by installing a WaterSense-labeled shower head.
Is 2.5 gpm low flow?
Unfortunately, there is no firm definition of low-flow, but it’s generally accepted that anything using 1.5 gallons per minute (gpm) or less is considered “ultra low flow,” while anything using 2.5 gallons per minute to 1.5 gallons per minute is considered “low flow.” Nowadays, thanks to standards set by the government Jan 18, 2018.
What is typical shower flow rate?
In an average home, showers are typically the third largest water use after toilets and clothes washers. The average American shower uses 17.2 gallons (65.1 liters) and lasts for 8.2 minutes at average flow rate of 2.1 gallons per minute (gpm) (7.9 lpm).
Does higher GPM mean more pressure?
GPM stands for gallons per minute. It refers to the flow rate or the volume of water that moves through the pressure washer’s nozzle every minute. Think of GPM as rinsing power. The higher a pressure washer’s GPM, the quicker you can wash a surface clean.
Is 1.8 GPM good for a shower head?
Since 1992, a maximum of 2.5 GPM is the federally mandated flow rate for new shower heads. This means no more than 2.5 gallons of water should flow out each minute. If your current shower head was made in the 1980’s or 1990’s, its flow rate could be 3.5 GPM or more!.
What is a good water pressure for a shower?
While you don’t want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that’s between 60 and 70.
What is a good shower pressure?
If the flow rate is less than 10 litres per minute, you have low water pressure. A flow rate between 10 and 15 litres per minute is considered acceptable but can be improved. A flow rate that is above 15 litres per minute will be regarded as good.
How can I make my shower water pressure stronger?
How to increase water pressure in the shower Clean your shower head. Replace the shower head. Install a shower pump. Installing a pressurised unvented cylinder. Install an electric shower with a cold water accumulator tank. Install a power shower.
Is 2 gallons per minute a good well?
Typical numbers for well recovery rates (if measured honestly over a 24-hour period) run from a fraction of a gallon per minute (a terribly poor well recovery or flow rate) to 3 gallons a minute of water flow (not great but usable) to 5 gallons per minute (just fine for residential use) to more than 10 gpm (a great.
How many GPM is a low flow shower head?
The current standard today is a shower head that dispenses 2.5 gallons of water each minute, or lower flow shower head which disperses 2 gallons or less of water per minute.
What is the difference between 2.0 GPM and 2.5 gpm?
A 2.0 GPM shower head will output two gallons of water in a single minute. Likewise, a 2.5 GPM unit will provide 2.5 gallons of water in the same amount of time. If three household members shower this much each day, it adds up to a difference of over 150 gallons of water each week, or 600 gallons each month.
How do you measure shower GPM?
Instructions for measuring the water flow rate at a faucet or shower Turn on the water. Time how long it takes to fill the container using your stop watch or phone (in seconds). Divide 60 by the number of seconds it took to fill your container (ie. The result is the flow rate of that application in gallons per minute.
What is a high flow shower head?
Most standard shower heads are rated around 2.0 GPM, with the maximum flow rate being 2.5 GPM. These high-flow rate shower heads deliver 2.5 gallons of water each minute, or 25 gallons of water during a 10-minute shower.
