Table of Contents
Various companies make garboard drain plugs, basically threaded bronze fittings that securely plug a drain hole when the boat is afloat and can be opened when it’s on the hard to let out rainwater. It’s better to go for one where both the flange fitting and the plug are bronze. Some are a mix of brass and bronze.
What is a Garboard on a boat?
/ (ˈɡɑːˌbɔːd) / noun. nautical the bottommost plank of a vessel’s hullAlso called: garboard plank, garboard strake.
Where is the Garboard on a boat?
The garboard strakes are the two immediately adjacent to the keel on each side. The word derives from traditional wooden boat building methods, used in both carvel and clinker construction.
What is a transom plug?
This is a drain plug. When removed from the bottom of your boat’s transom, water drains out. When inserted in the transom, it prevents water from coming back in. “Install drain plug” is usually the first item.
Are all boat drain plugs the same size?
Hole Diameter The most common for today’s recreational boat is one that fits a 1-inch diameter hole. Whichever garboard drain fitting you choose, make sure matches the transom hole and that there is enough surface around the hole to accommodate the size of the flange without it hanging below the bottom of the transom.
What is the meaning of Garboard strake?
Noun. 1. garboard strake – the first wale laid next to the keel of a wooden ship.
Do sailboats have drain plugs?
Most large sailboats don’t have a drain plug because the cockpit drains are designed to be above the water line and are open all the time.
How do you install a Garboard drain?
To install the fitting, simply drill a pilot hole, angled slightly downward, through the hull’s side at the lowest point in the bilge. After that, use a hole saw the same diameter as the stem on your garboard drain—depending on the maker, this will be up to 1 1/8in—to cut the hole proper.
What are chines on a boat?
A chine in boat design is a sharp change in angle in the cross section of a hull. The chine typically arises from the use of sheet materials (such as sheet metal or marine ply) as the mode of construction.
Does the drain plug on a boat go on the inside or outside?
It must be put in from the outside. You’d have to cut it off to put it in from inside. Many boats now come with a cable or strap attached to the boat plug from the inside.
How does boat drain plug work?
A drain plug is a plug that is located at the bottom of your boat’s transom. When you remove this plug, water drains out. If you replace it, it prevents water from coming back in. It is highly important that you remember to drain the water from your boat and then put the plug back in while your boat is on land.
How does AT handle drain plug work?
T-handle drain plugs are an easy and effective way to plug transom drain holes. Usage is easy, just insert the plug in the hole and give the handle a turn to expand the rubber and hold the plug in place. Offered in Brass to fit 1″ and 1 1/4″ diameter holes. Offered in Stainless steel to fit 1″ diameter holes.
What size thread is a boat drain plug?
PWCDOCTOR Standard Threaded Boat Drain Plug 1/2″ NPT.
How do you measure a drain plug?
To determine the right size of plug, you need to measure the diameter of the drain mesh or the underside of your current plug. Then you’ll be able to shop for the style of sink plug you want and be able to choose the right size the first time.
What is a sheer strake?
Definition of sheer strake : the upper strake of shell plating at the main deck in a steel ship or the top line of planking in a wooden ship.
What is coffin plate in ship?
Coffin plate: the plate joining two side plates over the keel of a vessel at the stern which in plan view creates a shape similar to a coffin lid. Sheer strake: It is the topmost strake on ship side.
What is bilge strake?
Bilge Strake is the strake at the turn of bilge extending outward to a point where the side rises vertically. Breast Hook is a triangular plate bracket joining port and starboard side structural members at the stem. Also called side port.
How many drain plugs does a boat have?
All boats (except ProStar) have two drain plugs, which allow water to be drained from the boat when the boat is OUT of the water.
How does water get into the bilge of a boat?
Bilge water enters from an array of different sources, including but not limited to Prop and rudder shaft packing, a weak or rusty hose clamp, dry rotted or damaged hoses, old and worn out thru hull fitting, mast drip, window or port hole leaks, air conditioning condensation sweat, engine exhaust leak, hatch leak, or a Feb 21, 2020.
Why do boats have a bilge?
The bilge is the lowest inner part, or bottom point, on a boat, and is designed to collect excess water. On vessels of virtually any size, a pump inside the bilge performs a very important function: to remove accumulated water by creating pressure or suction so that the water can be removed.
What is the deadrise on a boat?
A very common number thrown around when comparing boats, especially Center Consoles, is the Deadrise Angle of the hull measured at the transom. Put quite simply, it is the angle between a horizontal plane and the hull surface. A boat with “a lot of deadrise” is a boat with a deeper, sharper V-shaped hull.
What does chime mean on a boat?
April 27, 2020. The chine of a boat refers to the change in angle in the cross-section of a vessel’s hull. If you are looking at a boat straight on from the front or back, the bottom of the hull can be many different shapes. Some are extremely pointed while others are on the rounder side of the spectrum.
