Table of Contents
The backset is the distance from the edge of the door to the spindle mechanism on the latch. Usually for a 63mm case measurement it will have a 44mm backset and for a 76mm case measurement will have a 65mm backset. The backset you choose is where your door knobs will sit on the door (where the spindle goes through).
How do you measure a door backset?
The backset is the measurement from the edge of the door to the center of the bore hole. Most door handle sets feature a 2-3/8″ or 2-3/4″ backset. To determine the backset on your door, measure the distance from the outer edge of the door, to the center, or highest point of the bore hole.
What backset should I use?
The backset is the distance from the edge of the door to the center of the 2-1/8-inch bore hole. In the United States, there are two common backsets for residential door locks: 2 3/8 inches and 2 3/4 inches. Pack your locks with a 2-3/8-inch or 2-3/4-inch latch, depending on which backset you specify.
What is the typical backset for residential exterior doors?
Backset: Measure from the edge to the center of the drilled knob area; 2.375-inches (2 3/8-inches) is the modern standard.
What does 40mm backset mean?
‘Backset’ is the distance from the front of the lock to the centre of the spindle as shown here. Almost ALL domestic mortice locks and tubular latches are supplied with either a 44mm or 57mm backset length.
What is a backset on a door latch?
The backset is the distance from the edge of the door to the spindle mechanism on the latch. Usually for a 63mm case measurement it will have a 44mm backset and for a 76mm case measurement will have a 65mm backset. The backset you choose is where your door knobs will sit on the door (where the spindle goes through).
What is the most common backset?
Standard backsets are either a 2 3/8″ backset, or 2 3/4″ backset. The most common backset is 2 3/8″ but 2 3/4″ is also quite common – usually used on exterior doors. Sometimes it’s easier to measure from the edge of the door to the highest point on the bore hole.
What is case and backset?
The backset measurement is the distance from the centre of the keyhole, to the leading edge of the lock. The most common sizes here are 44mm (on a 64mm / 2.5″ lock case), and 56mm (on a 76mm / 3″ lock case).
Are all door latches the same size?
We generally recommend that a 76mm Overall Latch Size is ordinarily the best size for most lever handles. The larger sizes of latch are usually used for Door Knob furniture. We would usually recommend using the 102mm (4”) Tubular Latch or larger for a door knob, but the 76mm (3”) can be used as an absolute minimum.
What size backset do I need?
You can work out the size of the lock by measuring the distance from the edge of the door to the centre of the door handle or knob. This measurement will give you the approximate size of the backset which will allow you to identify which size lock or latch you have.
What determines backset on a door knob?
Backset: A backset is the distance from the center of the cross bore, to the edge of the door. To determine the correct backset measurement for your door, you need to measure the distance from the edge of the door to the center of your cross bore.
What is a door latch?
Door latches are a type of mechanical hardware used to fasten doors and keep them shut. A door latch uses a fastener attached to two ordinarily separated surfaces, most often the door and the frame, to prevent the door from swinging while still allowing normal operation when the latch is released.
How do you measure a backset on a mortise lock?
You can measure the mortice locks by measuring the backset and the centre. It is also advised you measure the case width and height and the forend length and width. Backset – The backset is measured through measuring from the centre of the keyhole to the forend of the mortice lock.
What is a Mortice?
A mortice (also spelt mortise) is a cavity or slot, usually rectangular, cut into a piece of wood or stone in order to receive a matching insert of the same dimensions.
Are door knobs universal?
Choosing the right door knob is more than simply a matter of appearance. The standard size for a door knob diameter is either 2 3/8 inches or 2 3/4 inches and these knobs will usually fit doors that are anywhere between 1 3/8 inches to 1 3/4 inches thick.
What size is a deadbolt hole?
The deadbolt lock set will come with a template to help you with measurements. Be sure to use the correct size drill bits specified in the lock set instructions, though most standard deadbolts require a 2 1/8-inch hole saw for the lock bodies and a 1-inch spade bit for the sliding bolt assembly.
What is adjustable backset?
When replacing a door deadbolt, it might be necessary to adjust the lock’s backset. The backset is the distance between the edge of the door and the center of the lock hole on the door. Adjusting the backset ensures the deadbolt locks completely once you install it in the door.
