Table of Contents
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. Rear-outlet toilets are configured a bit differently.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
Can you replace a 12 inch rough-in toilet with a 10-inch rough-in toilet?
A toilet with a 12-inch rough-in will definitely not fit into a space with a 10-inch rough-in, but a toilet with a 10-inch rough-in actually has extra space in a 12-inch rough-in space.
Do all toilets have a 12 inch rough-in?
Most toilets will have a 12 inch rough-in. Toilets with a 10- or 14-inch rough-in measurement are a little less common, so you might have less of a selection of toilets of this size. If you’re replacing an existing toilet, look for a replacement toilet with the same rough-in.
How do you measure toilet rough-in?
The rough-in measurement of a toilet refers to the span between the wall behind the toilet and the center of the waste pipe. To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor).
Can you replace a 14 inch rough in toilet with a 12 inch rough in toilet?
You can, but the back of the toilet tank will be two inches further away from the wall. The “rough-in” dimension refers to the distance from the wall framing (½-⅝″ behind the finished wall surface) to the center of the sewer pipe on the floor. Standard rough-in is 12 inches.
Why would I want an elongated toilet bowl?
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
What is the distance between toilet and wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
What measurements do you need to replace a toilet?
Make sure you measure from the centre of the bolts, up to the drywall (as opposed to the baseboard). If there are four bolt caps, be sure to measure from the center of the rear set. Toilets come in 10”, 14”, and most commonly, 12” rough-in dimensions.
What is rough in?
: to make a rough or unfinished version of (something, such as a design) as the first step in creating the finished version Rough in the lettering on your poster.
What is the difference between a 12 and 14 rough-in toilet?
The main difference between 12-inch rough-ins and 14-inch rough-ins is in their size (proportions). Depending on the type of bathroom, 12-inch rough-ins are generally more used than 14-inch rough-ins, but they both have merits, which means that you sometimes need to reduce the space from behind the tank.
What is an ADA toilet?
A comfort height toilet is sometimes known as an Americans with Disabilities Act (ADA) toilet because the height matches that used for ADA-compliant toilets, 17 to 19 inches from floor to seat. This is like the height of a chair. The height of a standard toilet is about 15 inches from floor to seat.
What is the standard size of a toilet room Australia?
A length of between 1200 and 1500mm is usually sufficient. If you’re creating a separate toilet room, you’ll need to allow for more space. The standard door width in Australia is 820mm plus and architrave and wall space either side, so it’s likely you’ll want the room to be at least one metre wide.
Can you replace a 13 inch rough-in toilet with a 12 inch rough-in toilet?
That’ll be your rough-in. If your distance if 13″ and you have a 1″ gap between the tank and the wall, then yes, your existing toilet is probably a 12″ toilet. You can indeed have two 12′ toilets that differ in size from one another.
Does rough-in size matter?
Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. If the base of the new toilet is shorter than the distance between the rear bolt holes and the wall, it should fit.
How many inches does an offset toilet flange move?
The typical offset is 12-inches for most residential toilets. As a result, the toilet had 4-inches behind the tank. It looked like it was trying to participate in the activities of the bathroom rather than sit quietly until needed.
What is better elongated or round toilet?
Most people find elongated toilet bowls to be more comfortable, but in a small bathroom, a round bowl can save space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures max out at 28″. Because round bowls are less expensive than elongated bowls, they save a few dollars, too.
Are 1 piece toilets better?
One piece toilets are typically heavier and easier to clean, and there’s less space for bacteria to grow. Because two piece toilets feature a detachable tank, they’re more customizable for preferred styles and heights. Both styles can include bells and whistles like bidet attachments or low-flow energy saving.
Can you put a round toilet seat on an elongated toilet?
While you can install a round toilet seat on an elongated toilet, it isn’t recommended. A round toilet seat will not fully cover the toilet bowl rim of an elongated toilet leaving the rim exposed.
