Table of Contents
But there is a good chance your ballast could be the cause of your lighting woes if your lights are dim, buzzing, changing colors, or flickering rapidly. You should check all parts of the fixture, including the bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit.
What are the signs of a bad ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
When should a ballast be replaced?
When your fluorescent light flickers or makes a loud and annoying hum, a degrading ballast is the cause. The ballast takes in electricity and then regulates current to the bulbs. A typical ballast will generally last about 20 years, but cold environments and bad bulbs can decrease this lifespan significantly.
What causes a ballast to go bad?
Every ballast has an ambient operating temperature range and UL location rating. When it’s too hot or too cold, the ballast can burn or fail to start your lamps at all. Heat combined with prolonged condensation inside an electronic ballast can cause corrosion and ballast failure.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
How do you know if it’s the bulb or ballast?
Take out your current bulbs and replace them with the new bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
How do you tell if a fluorescent ballast is bad?
If the ballast is bad, the needle on the multimeter will not move. If the ballast is still good, the needle should sweep to the right across the face of the multimeter. Install a new ballast, if necessary. Replace the ballast cover on the fluorescent light fixture.
How long do ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How much does it cost to replace a ballast?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Why does my fluorescent light work sometimes?
If a fluorescent tube blinks on and off-a slower and more distinct process than flickering-the fault may lie in loose wiring or in another component, called the ballast. The ballast is almost always to blame if the fixture hums during operation.
Why do fluorescent starters fail?
Starters have two failure modes, the bimetal gets weak and delays opening keeping the filaments on too long, the contacts burn and the filaments don’t light up during the starting phase.
Why do fluorescent bulbs fail?
Loss of Mercury Over time, as the mercury liquid is changed into a gas, some of that gas will become permanently absorbed into the phosphor coating. Since fluorescent lamps are now being made with lower amounts of mercury than in the past, this has now become a much more common problem for the failure of the fixtures.
Why do fluorescent lights not turn on sometimes?
If you find your fluorescent light won’t turn on sometimes, there could be a variety of reasons why. It could be as simple as needing to replace the bulb or plug the light itself in; or, it could be something more serious, such as a blown fuse or a damaged/dying starter.
Can a fluorescent light work without a ballast?
Reverted question “ Can I make a fluorescent light work without a ballast?” yes, you can, but you need something to reduce the current as the bulb warms up. So, you can drive a fluorescent with a pulse width adjustable power supply, but this is what is in an ‘electronic’ ballast.
Will LED lights work with bad ballast?
Can LED lamps work off of existing ballasts? Yes, if they have an internal driver than can work off that ballast. Philips, for example, has designed a tube that is compatible with an existing electronic ballast.
Is ballast needed for LED tube?
No LED bulbs require a ballast, although some are engineered to work with an existing ballast. You will find ballast-compatible or “plug-and-play” LEDs that are designed to replace linear fluorescents, compact fluorescents, or HIDs. Incandescent and halogen lamps do not require a ballast.
