Table of Contents
How do you figure out what gears you have?
Rotate the marked tire one revolution while counting how many times the driveshaft rotates. eg, If your driveshaft made 3 3/4 revolutions, that would determine a 3.73 gear ratio. If you get approximately 2 3/4 revolutions, you have a 2.76 gear ratio.
What gear ratio do I have by Vin?
The gear ratio is usually listed in the VIN code located on driver’s door, the glove box, or the ID plate on the dashboard. Count the times a rear wheel goes around for one driveshaft turn: if its 3 1/2 it’s a 3.50:1. Divide the number of teeth on the ring gear by the number of teeth on the pinion gear.
How do I know my rear gear ratio?
Turn the wheel TWO revolutions and count the number of driveshaft turns. The number of driveshaft rotations will help you determine your rear axle ratio. For example, if it turned 3 and a half times, it’s a 3.50:1 ratio. If it turned 4 and a quarter times, it’s a 4.25:1 ratio.
How can I tell what gear ratio I have without pulling cover?
So an easy way to determine your actual gear ratio is to check the tag attached to the differential cover by the cover bolts. On the tag there should be some numbering such as 3.54 or 3.73, either of those numbers will give you the stock axle ratio.
How do I know what gear ratio My bike is?
The simplest is the ratio between the chainring and rear sprocket: divide the number of teeth on the chainring by the number on the sprocket. Let’s say the chainring has 48 teeth, the sprocket 16. That’s 3:1. For each crank revolution, the wheel turns three times.
What gear ratio do I have f150?
Write down the number in the lower left-hand corner of the tag. It will look like “3.23” or “3.50.” This is the gear ratio.
How do I know what rear end I have?
To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.
What does the 8th digit of a VIN mean?
Vehicle Description Section The fourth through eighth digits describe your vehicle’s model, body type, restraint system, transmission type, and engine code. The ninth digit is the check digit, which is used to detect fraudulent VINs.
What gear ratio is GT4?
The 19% reduction in the GT4 final drive ratio (from 3.89 to 4.62) will have a similar effect on the GT4’s performance, improving 0-60 time by approximately 4/10ths of a second and improving lap times on most longer/fast US tracks by at least a second.
Are 3.73 or 4.10 gears better?
4.10s are going to accelerate faster and decelerate faster on lift. However the trade off is greater fuel consumption per mile driven and higher engine speed per given road speed. In basic terms the 4.10s will feel quicker and 3.73 will feel faster.
What gears for what speed?
Remember each car will be geared slightly differently, but a good rule of thumb for changing gears is that first gear is for speeds up to 10 mph, second gear is for speeds up to 15 mph, third gear is for speeds up to 35 mph, fourth gear is for speeds up to 55 mph, fifth gear is for speeds up to 65 mph, and sixth gear Oct 22, 2019.
What are 3.73 gears good for?
A numerically higher axle ratio provides a mechanical advantage to send more of the engine’s available torque to the rear tires (and front tires, in a four-wheel drive vehicle), but you pay the price at the fuel pump. So, a truck with optional 3.73 gears will tow a heavier trailer than one with 3.55 or 3.21.
What gear ratio is a Dana 35?
The Dana 35 is used extensively in the Jeep models. This axle had a GAWR up to 2700 lbs.Available Gear Ratios. Ratio:1 Pinion:Ring Teeth 3.31 13:43 3.54 13:46 3.58 12:43.
What rear end do I have by VIN?
Identify the VDS section, the fourth through eighth digits of the VIN. This section typically includes information such as the vehicle model, engine size and body type. While not every vehicle manufacturer includes gearbox ratio information in the VDS, this will be where the information is found if it was included.
What gear should I use on a flat road?
For riding on flat roads, it is recommended to use the middle gear. It is a common choice among bikers as it helps you reduce pressure from your feet onto the pedals.
What is gear 7 on a bike?
Number 7 on your right shifter is the hardest gear for going really fast, and it puts your chain on the smallest rear sprocket. Never use the full range of rear gears when you’re in either the small or large front sprockets (number 1 or 3 on the front shifter).
How do you use gears on a bike for beginners?
A long push (with two clicks) will move the chain into a larger, easier gear in the rear (right hand) and a larger, harder gear in the front (left hand). A short push (with one click) will move the chain into a smaller, harder gear in the rear (right hand) and a smaller, easier gear in the front (left hand).
