Table of Contents
What gauge wire does Minn Kota trolling motor use?
CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE MOTOR THRUST/MODEL MAX AMP DRAW WIRE EXTENSION LENGTH 5 FT 30 lb. 30 10 AWG 40 lb., 45 lb. 42 10 AWG 50 lb., 55 lb. 50 8 AWG.
What gauge wire should I use for a 12 volt trolling motor?
Wire Gauge And Circuit Breaker Size Guide Cell Amps drawn 15 ft length 12 volt 30 8 awg 12 volt 42 6 awg 12 volt 50 4 awg 24 volt 42 8 awg.
What size wire is needed for 24 volts?
If you have a 24V supply for a 200 amp device, we will assume that the wiring is copper and has a typical insulation and installation type. With a wire distance of 25 feet and a voltage drop of 3%, you will need a wire size of 4/0 AWG.
Is my Minn Kota 12 or 24-volt?
The nameplates are most often found in the foot petals of the motor. Otherwise, you can look at the configuration of the trolling motor batteries to find the volts. Open the hood and look at the battery. If you see 6 cells, it’s a 12-volt battery, but if you see 12 cells, it means it’s a 24-volt battery.
What size wire do you use for a trolling motor?
Always keep in mind that you’ll need an 8-gauge wire for a 50-amp trolling motor and a 6-gauge one for its 60-amp counterpart.
What size battery do I need for a 55 lb thrust trolling motor?
For a 55 lb thrust in a trolling motor, you will at least need the battery size of 240Ah rating. Depending on the speed, you will be using approximately 20-40 amps.
Do I need a circuit breaker on my trolling motor?
It is highly recommended that a circuit breaker or fuse be used when installing a trolling motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.
Why does my trolling motor have 3 wires?
The three wire plug is for a 12/24V system. On a 12/24 you have a 12V hot, 24V hot, and a ground.
Can you use a 24 volt battery on a 12 volt trolling motor?
The answer is NO. Essentially, you have a 12 volt motor. If you try to run it on 24 volts, you will burn it up.
How do you wire a motor for a trolling motor?
24-Volt Wiring Loosen the two terminals on the circuit breaker supplied with the trolling motor. Slide the red wire from the motor over one of the terminals and tighten it down. Loosen the positive terminal on the second battery. Slide the red wire over the positive terminal on the second battery and tighten it down.
Is 12V better than 24V?
24V systems are beneficial because you can use smaller diameter wire and reduce amperage by two times. You can actually run a wire 2x smaller than an equivalent 12V circuit. This is because the higher voltage requires less current to produce the same power.
How do I know what gauge wire to use?
To determine what gauge wire you need, consider the carrying capacity and the amount of current the wire needs to conduct (measured in amperage or amps). Wire gauge is directly related to how many amps you need to run through it. The distance you need the wire to go can also impact the gauge of wire you need.
Does wire gauge affect voltage?
The wire gauge refers to the THICKNESS of the wire. As such, lesser the thickness of a wire, higher will be its resistance and vice-versa. Consequently, due to higher resistance, flow of current will be reduced and voltage drop across the length of the wire will increase.
What happens if you run a 24 volt trolling motor on 12 volts?
24v hooked to 12v will spin for a while on a full battery but there will be no torque. You could stop it with your hand. It is like running your motor with half the spark plugs missing.
What is the difference between a 12 volt and 24 volt trolling motor?
Trolling Motor Voltage & Batteries A 12-volt trolling motor is the most inexpensive and easiest to run. A 24- or 36-volt system will allow the angler to fish longer periods out on the water, as they draw lower amps while providing increased thrust for more power.
Does Minn Kota make a 24 volt trolling motor?
Minn Kota RIPTIDE SM RT/80/SM/BG SALTWATER TROLLING MOTOR-24V-80LB-62.
What gauge wire is needed for a 36 volt trolling motor?
You need the 6 gauge.
What does AWG stand for?
AWG (American Wire Gauge) is a U.S. standard set of non-ferrous wire conductor sizes.
How many amps does a trolling motor pull?
The Force trolling motor can run on 24 volts or 36 volts, and the chart below shows how a 24v setting will draw higher amps then running at 36 volts.24 Volt Power Source. Throttle Level Thrust Current 20% 45 N-m (10 lbf) 3 A 30% 70 N-m (16 lbf) 6 A 40% 101 N-m (23 lbf) 9 A 50% 140 N-m (31 lbf) 14 A.
What is orange wire on trolling motor?
The red wire is wired to the + terminal of battery #2. You have a jumper wire that is connected alos to the + terminal of battery #2 as well as to the – terminal of battery #1. Finally, the orange wire is connected to the + terminal of battery #1. Now at the trolling motor end.
