Table of Contents
uL. (none) Unbalanced load. uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load.
How do I fix my uL washing machine?
UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.
How do I fix the uL code on my Kenmore washer?
Unplug the washer. Plug the U.I. back in and then plug the washer back in. Codes should then be cleared.
How do I fix the code on my Whirlpool Cabrio?
Always disconnect the washing machine’s power supply before working on the appliance! First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea.
Why does my washing machine keeps unbalancing?
The most likely culprit is the suspension rods. These rods help to limit the amount of side to side and front to back movement that happens when a washer enters the spin cycle. If your washer is manifesting the banging noise of an unbalanced load with every spin cycle, contact us today.
How do you reset the sensor on a Kenmore washing machine?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
Can you reset a Whirlpool Cabrio washing machine?
How To Reset Whirlpool Cabrio Washer: Turn the washer off. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
Why won’t my Whirlpool Cabrio washer drain and spin?
The most common causes of a Whirlpool Cabrio not spinning are: Defective lid switch. Broken drive belt. Loose drive pulley nut.
What does uL mean on my Whirlpool Cabrio washer?
If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
What is LF code on Cabrio washer?
Whirlpool Washer LF Error is a water fill error, it stands for Long Fill. It means that the main control has not gotten a signal back from the water pressure sensor which means that water is not filling the tub or not filling the tub fast enough.
How do you rebalance a washing machine drum?
Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it.
How do you run a diagnostic test on a Kenmore washer?
3 Answers With the washer empty, close the door. Push “control/on” or “Start” Select “Drain/Spin” Select “No Spin” by pressing SPIN SPEED touchpad. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.) C:00 should light up and begin the diagnostic.
Why is my Kenmore washing machine not draining?
A Kenmore washer that won’t drain properly likely has a clogged pump. Try checking the drain to see if there’s any foreign object obstructing the valve or opening. If not, the drain pump might be damaged and need replacing. Those with newer washer models can also try performing a master reset.
Where is the balance ring on a Kenmore washer?
Balance Ring Basics Many Kenmore washing machines have balance rings at the top of their inner washtubs. The plastic rings are filled with water and saline and surround the tub. They help stabilize the washtub so it spins smoothly while adjusting for various laundry load sizes.
What is F1 code on Kenmore washer?
F1 code means the central control is not communicating with the central control.
What does OL mean on Kenmore Elite washer?
The OL error code indicates that the washer is overloaded. If the washer is not overloaded, this would indicate either a drag on the drive system or the control board is failing. Be sure nothing is on the floor under the washer that could be causing a problem.
How do you fix an unbalanced front load washer?
Level your washer by putting 4 towels in the washer and put the washer in spin. Wait until it gets to high spin and adjust the front legs to level your front load washer. The out of balance issue will smooth out by turning the legs to touch the floor in an even manner.
How do I know if my washing machine balance ring is bad?
The balance ring is filled with fluid. This fluid helps to dampen the vibration of the washer. If this fluid leaks out of the balance ring, the washer tub will vibrate and shake during operation. Check the balance to determine if is still filled with fluid.
How do you rebalance a front load washer?
How to Balance Front Load Washers Open the front-load washer door. Manually redistribute the load inside the drum. Add more items to the wash. A single, bulky item, such as a comforter or blanket can cause the unbalanced load. Avoid overloading your front-load washer.
How do I reset the control panel on my Whirlpool washer?
Follow these steps to reset a Whirlpool washing machine: Make sure the power to the washer is turned on at the wall, but keep the Power button on the control off. Hold the Program button down while simultaneously pressing the Water Level button two times. When done correctly, the control panel lights should illuminate.
