Table of Contents
“Sud” or “Sd” in display of your Maytag Washer This error code indicates excessive detergent suds occurred during the cycle. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. The washer will not be able to spin out water with the excess suds.
How do I fix my Maytag SD error?
Maytag acknowledges that error codes like “Sd” sometimes appear by mistake. Push the “Pause/Cancel” twice or “Power” button once to remove the code from the screen and try using the washer again. If the code returns, unplug the washer for 60 seconds and try the cycle again before calling for assistance.
How do you get Sud out of a washing machine?
Wipe the interior of the drum with a clean, dry cloth to remove excess soap residue and bubbles, changing it out as needed. Set the machine to a full load and allow it to fill with water before adding 2 cups of distilled white vinegar. Complete the wash cycle. Run a second rinse cycle to remove lingering residue.
How do I clean the filter on my Maytag washer?
The quickest way to clean out your filter is to remove it from the unit and soak it in hot water, loosening any clog or trapped residue. If the filter cannot be removed, clean it out with brush. Some filters are disposable, so instead of cleaning them you can just throw them away and put a new one in place.
Why does my washer keep saying SD?
There are too many suds in the washing machine. The washer will not be able to spin out water with the excess suds. When “Sud” or “Sd” is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the washer pauses the tumbling and adds water for additional rinsing.
How do I clear the error code on my Maytag commercial washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle.
How long does Sud error last?
When there is an excessive amount of detergent present, the display flashes a SUD Error number, and the washer slows its work to allow the foam to dissipate before continuing the cycle. It can take anything from 5 minutes to 40 minutes, depending on how much powder is in the water.
What causes suds in washing machine?
What an overload of suds means usually is that you are using too much detergent. The more detergent in the water, the more suds it will produce. If you have soft water, by following detergent directions, you are actually using too much detergent. This will cause your overproduction of suds.
Are suds necessary to clean?
Soap Science: Suds Don’t Clean Your Dishes As it turns out, there isn’t. Bubbles have little to nothing to do with cleaning power, even though most people think they do.
Does a Maytag washing machine have a filter?
Washers and dryers such as those by Maytag have filters to catch lint. Maytag produces a wide range of home appliances, including washers and dryers. While dryer lint filters and screens should be cleaned out after each use, washing machine lint filters can be cleaned out less frequently.
Where is the filter on a Maytag top load washer?
In top-loading machines the filters are in the center of the agitator tube. They can be removed by taking off the agitator cap and pulling the filter upward. Lint and debris can then be removed by hand before replacing the filter.
How do I clean my Maytag washer without affresh?
If you don’t have affresh® tablets, you may be able to use liquid chlorine bleach. Check your owner’s manual for instructions on how to clean with bleach. Close the door and select your washer’s cleaning cycle. For top load washers, when the cycle ends, run a rinse and spin cycle to clear away any excess cleansers.
How do I fix my SUD error?
The washer has detected too many soap suds; it should pause automatically and wait for the suds to dissipate. Making sure you are using a high-efficiency detergent, not using too much detergent, removing detergent residue from the washer, and cleaning the drain pump filter should resolve the issue.
Why is my washer flashing Sud?
It means you are using detergent improperly. If your washing machine has the word “SUDS” on the display, it has detected an over-sudsing condition, and will stop for a short period to allow the suds to dissipate. This error code is usually caused by too much detergent, or the wrong type of detergent.
How do you clear a F28 code on a Maytag washer?
An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit. Rebooting the control unit is accomplished in less than 10 minutes, even by the novice.
How do I reprogram my Maytag washer?
If an error message causes your Maytag washer to not run properly, reset the washer to clear the error message.How to Reset a Maytag Washer Press the “Power/Cancel” button. Push the appropriate button to choose a new cycle. Press “Start/Pause.” You have now reset your Maytag washer.
