Table of Contents
The Whirlpool washer Lo FL error code is displayed when water is not detected entering the washer or it’s not filling the washer fast enough.
What does Fl mean on washing machine?
If Samsung Washer FL Error Code appears on the display panel, it’s likely a door lock malfunction. It indicates the door lock cannot be locked after several attempts.
What do you do when your washer says Lo FL?
If the washer has an F8 E1, LF, or LO FL error, the door will be locked, and the control will be unresponsive.If pressing Power does not work: Unplug the washer or disconnect the power for one minute. Plug in the washer or reconnect the power. Re-select the cycle and press Start.
What does Fl mean on a front load washer?
Samsung Front-Load Washer Fault Codes Fault Code Washer Problem LO or FL Door lock error ds Door is not locked dc Unbalanced load Sud (F70) Too many suds.
How do I fix a Whirlpool washer error?
Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.
What is FL error code?
The P2 or FL error code is an indication that the drain pan in the unit is full.
What does LoC mean on my Whirlpool washer?
If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock and need to de-activate it to allow the washer controls to function. Some models will look like the following: This error code does not mean “Door Locked”.
How do you reset a Whirlpool washing machine?
Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
Where is the water level switch on a Whirlpool washer?
Look for the water level switch on the right side of the cabinet toward the back of the washer. The round water level switch attaches to the side of the cabinet. A rubber tube connects the water level switch to the washtub.
How do you clear the error code on a Whirlpool top load washer?
System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).
How do I fix the LO FL on my Whirlpool washer?
Whirlpool Washer Lo FL Error Make sure the water supply is turned on and you have proper water pressure being supplied to the machine. Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.
What does rL mean on a washing machine?
The “rL” error code means that a load has been detected in drum during Clean Washer with affresh® cycle. The Clean Washer cycle is meant to run empty, with no clothing inside the washer. Remove items from washer drum and restart Clean Washer with affresh® cycle.
Why does my washer say low flow?
If you only notice low water pressure when using the hot water setting, then you probably have a clogged hot water line (or vise-versa for cold water). The easiest solution to this problem is to replace the clogged line with a new one. Water lines can be purchased either online or at most major home improvement stores.
What does F25 mean on a Whirlpool washer?
The F25 error is a problem with the washer motor’s tachometer. It means the main control cannot determine the spin speed of the motor. This error can be caused by the motor, the motor control board, the main control board, or a wiring issue between all.
What does F06 mean on a Whirlpool washing machine?
A Whirlpool washer error code E01/F06 indicates that the washer’s motor control unit (MCU) is having trouble communicating with the washer’s central control unit (CCU). In most cases, the issue is caused by a damaged MCU circuit, usually caused by an overload.
What does f1 mean on a Whirlpool Duet washer?
The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.
What is FL aircon?
The P2 or FL error code (depending on model) indicates that the drain pan in the unit is full. Under normal operating conditions, the drain pan will not need to be emptied. The unit is designed with a slinger fan that is mounted above the drain pan.
What does Fl mean on Kenmore Elite washer?
The FL error code means: Flood Condition: FL flashes if any overfill condition occurs. This condition occurs when excessive water in the tub causes the overfill switch to trip. The control must realize that the trip was due to an overfill condition instead of a suds lack condition in order for FL to be displayed.
How do I turn off the LOC on my Whirlpool washer?
Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
How do I force my Whirlpool washer to unlock?
Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.
