Table of Contents
What do I need to set up a hot tub?
Getting a hot tub installed in the backyard is a much simpler process than you might imagine. Basically, you need to make sure that you have access to the backyard; a solid, level place to set the spa; and electricity, and a garden hose in close proximity.
Do hot tubs need to be plumbed in?
Hot tubs are fully portable units and are NOT plumbed in. You will need to be within a hose distance of a water supply to fill the hot tub up. But that’s it, no pipes or permanent water supplies are necessary.
Can you plug a hot tub into a regular outlet?
Most hot tubs require a 240v electrical hookup—which for most people means you have to call an electrician and have new wiring done. However, a Plug n’ play spa runs on standard 110V power, which can be plugged into most standard household power sources without the need for additional wiring.
What kind of support do you need for a hot tub?
A solid, flat surface is required for a hot tub. A concrete slab is effective at supporting a hot tub. This must be installed along with the concrete deck footings of your deck. For most, a slab four inches thick should suffice, unless one decides to get a very large hot tub then something thicker should be poured.
What chemicals do I put in a hot tub?
What Hot Tub Chemicals Do You Need? Products to Adjust pH. To keep your hot tub pH in check, you should have a pH increaser and a pH decreaser. Non-Chlorine Shock. A shocking agent releases oxygen into the water, which serves a similar function as chlorine. Sequestering Agent. Sanitizer. Defoamer. Calcium.
How soon can you use hot tub after adding chemicals?
Do not use a hot tub right after you add chemicals. You should wait at least 2 hours before using the hot tub again. The chemicals need time to work their magic and sanitize the water. Also, a higher concentration of chlorine is best because you’ll need to add chemicals less often.
Do you need an outdoor socket for a hot tub?
If you’re looking for a 32A hard-wired hot tub which generally will have higher performance for a more powerful hydrotherapy massage, you need a different type of outside socket. The hot tub needs to be protected by an MCB (mains circuit breaker) and needs to cover the maximum amperage of the hot tub (ie.
How much room do you need around a hot tub?
A good rule of thumb for a hot tub is to give yourself about a foot of space on each side of the tub. This leaves room for things like opening the cover. Most covers require at least 18 inches of space behind the tub as well as a few inches on the left and right side for the arm that helps you lift the cover.
How much is a heater for a hot tub?
How Much Does It Cost to Replace a Heater in a Hot Tub? Hot tub heater replacement cost ranges from $225 to $650, including $150 to $500 for the heating element.
Can you run a hot tub with an extension cord?
Never use an extension cord for your best hot tub. The cord provided with your spa is the proper length and gauge for current to travel safely from the electrical outlet to your spa. An extension cord forces the current to travel a longer distance and may result in a voltage drop or the cord overheating.
Do hot tubs have to be hardwired?
The electrical connection to the hot tub must be single phase, 220-240 volt 4 wire. The four wires consist of two hots, one ground, and one neutral and must be hard wired to the terminals inside the hot tub control box.
Does a hot tub need 220V?
Most acrylic hot tubs require a 50-amp 220V electrical connection. These dedicated hook-ups require a licensed electrician for installation. Often called plug and play hot tubs, there are models that require a 15-amp 110V connection.
Can a concrete patio support a hot tub?
So long as it is flat and without grade, it will likely work for your new portable hot tub. Usually a concrete slab made to building code is suitable to hold a hot tub. However, many patios and other concrete slabs are pitched for drainage, which may make an unsuitable base for your hot tub.
Does a hot tub need to be on concrete?
A hot tub requires a stable surface — whether it’s a concrete slab, reinforced deck, or firmly compacted soil with crushed gravel. There’s also the option to have the hot tub installed in the ground but that still requires a concrete vault.
Can you put a hot tub on pavers?
A hot tub can be placed on pavers, but ensure that they can bear the weight of the hot tub, including water and persons. Ensure that the floor is level and solid. Most pavers are laid at an angle to improve rainwater removal. Such a slope is not suited for a hot tub.
How often do you put chlorine in a hot tub?
You should put chlorine in your hot tub at least once a week. However, some people prefer to add a small amount after each use. Finding the best water care routine will depend on how often and how many people use it. Chlorine levels should be between 1.5 and 3.0 ppm.
