Table of Contents
A Grounded Conductor is usually identified with the color white, although it can be gray. If the conductor is size 6 AWG or smaller, it must be solid in color or identified with three continuous stripes of color for the entire length of the conductor.
What is an acceptable color for the grounded conductor?
The Code states: The grounded conductor of a branch circuit shall be identified by a continuous white or natural gray color. Also, The equipment grounding conductor of a branch circuit shall be identified by a continuous green color or a continuous green color with one or more yellow stripes unless it is bare.
How is a grounded conductor identified?
Three continuous white stripes along the conductor’s entire length on other than green insulation. When can grounded conductors be taped at the terminations? 4 AWG or larger, a grounded conductor can be identified by a distinctive white or gray marking at the terminations. The marking must encircle the conductor.
Which is the grounded conductor?
According to the terminology in the CEC and NEC, the “grounding” conductor is for the safety ground, i.e., the green or bare or green with a yellow stripe wire. The word “neutral” is reserved for the white when you have a circuit with more than one “hot” wire.
What conductor can be any color except white light gray green or bare?
[310-12(c)] Ungrounded conductors (except for the high leg of a four-wire, delta connected system) can be any color other than white, natural gray, green, or green with yellow stripe(s). Although the colors for ungrounded (hot) conductors are not specified, there are some colors that are typically used.
What 3 colors are ungrounded conductors not permitted to be?
Ungrounded conductors shall be distinguished by colors other than white, natural gray, or green; or by a combination of color plus distinguishing marking.
What color is the grounded terminal?
In the US it is green in residential wiring. However this is just the safety ground. The neutral which is expected to be at ground potential but carries current is white. Green is standardized color used by many countries for a ground wire.
What is a white conductor?
The white conductor within a cable can be used to supply power to single-pole, 3-way, and 4-way switch loops, as well as travelers for 3-way and 4-way switching if permanently re-identified at each location where the conductor is visible to indicate its use as an ungrounded conductor.
What Colour must the outer finish of a grounded identified conductor of 6 AWG or smaller be?
(A) Sizes 6 AWG or Smaller The insulated conductor shall have a continuous gray outer finish. The insulated conductor shall have three continuous white or gray stripes along the conductor’s entire length on other than green insulation.
Can I use white wire for ground?
The National Electrical Code (NEC) says that white or gray must be used for neutral conductors and that bare copper or green wires must be used as ground wires. Beyond that are general, industry-accepted rules about wire color that indicate their purpose.
What color is the ungrounded wire?
Black Wires Wires with a black insulation coating are always used as hot wires, or ungrounded conductors. Hot wires are used to feed a switch or an outlet.
Which of the following colors is not permitted to be used to identify a grounded conductor?
Conductors with insulation or individual covering that is green, green with one or more yellow stripes, or otherwise identified as permitted by this section shall not be used for ungrounded or grounded circuit conductors.
Is a neutral an ungrounded conductor?
In any electrical system, the neutral is a grounded conductor that you must size and treat differently from ungrounded phase conductors.
What are the 3 most common conductors and their corresponding colors?
These colors correspond to standard wiring practices. Typically for 120/208V systems: Black, Red and Blue for phase conductors; White for neutral; and Green for ground.
What do black wires mean?
Black: Black wires are neutral wires and the wire is connected to a neutral bus bar inside the electrical panel. The bus bar is a conductive piece of metal used for the purpose of distribution. The black wire can be connected to another black wire, and as it is neutral, it does carry a charge.
What are the primary high voltage colors for ungrounded conductors?
No. The National Electrical Code does not have a required color code. Trade practice is to use black, red, blue for 120/208Y voltage systems and brown, orange, yellow for 277/480Y voltage systems. When are ungrounded conductors required to be identified?May 16, 2013.
What are ungrounded conductors?
An ungrounded conductor is a circuit conductor that carries current to the load. We usually call ungrounded conductors in a service, feeder, or branch-circuit phase conductors. You must also connect these same conductors to color-coded or marked terminals of electrical equipment.
What is the difference between the grounded and ungrounded conductor?
Grounded conductors are meant to keep people from getting shocked when using electrical devices or appliances. You’ll usually find them in outlets. They keep the metal of the outlet from getting hot and causing electrical shocks. Ungrounded conductors are also called the hot wire.
Is ground green or black?
US AC power circuit wiring color codes Function label Color, common Protective ground PG bare, green, or green-yellow Neutral N white Line, single phase L black or red (2nd hot) Line, 3-phase L1 black.
Is ground black or red wire?
The red wire is the power source and the black wire is the ground wire.
Can a ground wire be red?
In the standard wire color code, the hot wire in a cable with two conductors plus ground is black, and the extra hot wire in a three-conductor set is red. The standard ground wire color is either bare copper or green.
