Table of Contents
In dispersed clay slurries, flocculation occurs after mechanical agitation ceases and the dispersed clay platelets spontaneously form flocs because of attractions between negative face charges and positive edge charges.
What makes a good flocculant?
Polymers are useful as flocculants because they are robust molecules and sometimes carry charges. Because they are so large, small particles can get trapped in the curves of the polymer causing them to accumulate a mass heavy enough to prevent their retention in solution.
What is the principle of flocculation?
Coagulation – flocculation is physico-chemical process that facilitates the agglomeration of fine particles (colloids) contained in water to form a floc that can be easily filtered from water. Effluent (waste water) must be treated before it is discharged or before the water is re-used.
Does flocculant kill algae?
There are two major chemical treatments for algae: flocculant and chlorine. Flocculant, or floc, is a chemical and mechanical process that works fast but requires work on your part. Then, you must turn it off to give the algae time to settle. If you use chlorine shock, you should run the filter almost continuously.
Does flocculant affect pH?
Because flocculants can affect the pH level, you’ll want to start out with it at about 7.0 so you can make sure your sanitizer keeps working at maximum efficiency.
What chemical is used for flocculation?
Aluminum sulfate or alum (Al2(SO4)3), ferric chloride (FeCl3) and ferric sulfate (Fe(SO4)3) are the most widely used flocculants [1, 70]. These flocculants have a long history of use in removing colloidal particles from water and wastewater [15, 17].
How much alum do I put in my water?
Make an alum solution by adding 7.5 grams of alum to one liter of tap water.
What are the side effects of alum?
Side effects of Alum The excessive amount of alum intake may cause breathing difficulty, facial puffiness, pricking sensation & small ulcers on the skin, chest/throat tightness, and burns rarely seen in some cases.
How do you mix flocculant?
To optimize flocculant mixing system sizing, flocculant solutions are often designed to be mixed to 0.25-0.50% maximum concentration. Once dissolved, the flocculants will dilute readily with teed in water down stream of the flocculant feed pump to obtain the final target 0.1% concentration.
How do you dissolve flocculant?
Bleach or sodium hypochlorite can be used to break down polyacrylamide-based flocculants.
What can be used as a flocculant?
The following natural products are used as flocculants:
- Chitosan.
- Isinglass.
- Moringa oleifera seeds (Horseradish Tree)
- Gelatin.
- Strychnos potatorum seeds (Nirmali nut tree)
- Guar gum.
- Alginates (brown seaweed extracts)
What is difference between flocculation and Deflocculation?
The key difference between flocculation and deflocculation is that flocculation is the formation of flocs by the clumping of fine particles, whereas deflocculation is the dispersion of flocs to form a stable colloid. Flocculation refers to the formation of clumps from fine particles in a colloid.
Is alum a coagulant or flocculant?
To accomplish this, the water is treated with aluminum sulfate, commonly called alum, which serves as a flocculant. Raw water often holds tiny suspended particles that are very difficult for a filter to catch. Alum causes them to clump together so that they can settle out of the water or be easily trapped by a filter.
How fast does flocculant work?
How Long Does It Take to Work? The beauty of flocculants is that they work fast. Your pool can be cleaned in 24 hours, whereas with a clarifier, it takes a few days for the filter to do its job. The drawback, however, is that you have to vacuum the dirt out from the pool floor by yourself.
What causes flocculation to occur?
In dispersed clay slurries, flocculation occurs after mechanical agitation ceases and the dispersed clay platelets spontaneously form flocs because of attractions between negative face charges and positive edge charges.
What is flocculant powder?
Flocculant Powder are water soluble polymers used for flocculation in effluent treatment. It is useful for non potable raw water clarification, primary and secondary effluent clarification, improves solid settling and decrease the BOD load on the system.
What two chemicals are commonly used as water coagulants?
Aluminum sulfate (alum) is the most common coagulant used for water purification. Other chemicals, such as ferric sulfate or sodium aluminate, may also be used.
How do I make my pool water crystal clear?
How to Make Your Pool Crystal Clear Again
- Keep Up with pH and Chlorine Levels. Do you have a water testing device in your supply kit?
- Run That Filter. It’s recommended that you run your filter for 8 to 10 hours a day when using your pool.
- Skim, Skim, Skim. Yes, something that simple can be the trick to clear water.
- Shock the Pool Once a Week.
What does Flocculate mean?
flocculate in American English 1. to form into flocculent masses. intransitive verb. 2. to form flocculent masses, as a cloud or a chemical precipitate; form aggregated or compound masses of particles.
Why is flocculation important?
Used water can contain significant amounts of suspended particulate matter, which often takes long to sediment. Flocculation expedites sedimentation and ensures efficient solid/liquid separation.
Does alum increase pH?
Ionic species present in alum solutions are highly dependent on the degree of reaction with hydroxyl ions. It is tempting to say that “the composition is pH-dependent.” However, in the vicinity of pH=4.3 the composition of alum solutions changes a great deal with very little change in pH.
How can flocculation be prevented?
When particles of a suspension come close together they can form aggregates called flocculates which will settle more rapidly. To prevent that we often coat the particle with a charged surfactant. The charge (Zeta potential) acts to keep the particles separate and prevent flocculation.
Can you add too much flocculant?
Adding too much flocculant can cause its own issues. Flocculant is aluminum sulfate, which is designed to clump with the particles you’re trying to remove. But if you add too much, the flocculant will start to agglomerate with itself instead of those particles.
What is the difference between flocculant and coagulant?
Depending on the charge and chemical composition of your wastewater, flocculants can either be used on their own or in combination with coagulants. Flocculants differ from coagulants in that they are often polymers, whereas coagulants are typically salts.
