What Causes A Washing Machine Not To Drain

There are a few possibilities why your washing machine won’t drain. Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.

How do you fix a washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.

What causes a washing machine not to drain and spin?

If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.

How do I know if my washing machine drain hose is clogged?

If the hose is clogged, it can prevent the water from being pumped out of the machine. To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it.

Why does water stay in washing machine drum?

The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.

Where is the drain pump on a washing machine?

The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.

How do you manually drain a washing machine?

If not, follow these steps: Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.

How do I know if my washing machine drain pump is bad?

Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you’ll be able to feel them while you’re turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.

How do you position a washing machine drain hose?

In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.

Can you pour Drano down washing machine drain?

Can I put Drano down my washing machine drain? Yes. Drano or any drain cleaner can be used to unclog your washing machine drain, but make sure you run your washer without a load of laundry before normal use.

How much does a washing machine drain pump cost?

It can cost as little as $10 or as much as $75 or more. However, most homeowners pay between $25-$40 for a new pump.

Can a water pump get clogged?

When overly large solids or certain types of debris enter the water, some pumps are more prone to clogging. Clogged pumps with a full or partial blockage can quickly pose severe damage to the rest of your equipment, cause backups and can potentially delay your projects.

What cycle does a washing machine drain?

One of the principal functions of a washing machine is to drain the used, dirty water and replace it with fresh water during the rinse cycle. After clothes are rinsed, the washer drains again. To perform these actions, a washer uses a pump to remove the water from the tub through a drain hose.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

Can a washing machine drain into 1 1 2 pipe?

Drain and Trap Requirements A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers. As with all plumbing fixtures and appliances, a washing machine drain pipe must also contain a P-trap.

How do you drain an automatic washing machine?

If not, follow these steps: Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.

How much does it cost to unclog a washing machine drain?

How much does it cost to unclog a drain? Nationwide, the average cost to clean a clogged drain is $130-$180. This covers both the cost to find the clog and clear the drain. Most plumbing companies will charge a flat rate of $50 – $150 to come out, which also covers the first hour of work.

Can washing machine get clogged?

What causes washing machine clogs? Soap residue, dryer lint debris, and soiled clothing can all lead to clogs in your washing machine.