QA

What Causes A Toilet To Run Intermittently

A toilet that cuts on and off by itself, or runs intermittently, has a problem that plumbers call a “phantom flush.” The cause is a very slow leak from the tank into the bowl. This problem is almost certainly caused by a bad flapper or flapper seat.

How do you fix a toilet that runs randomly?

Solution 1: Replace the Flapper Use a sponge to clean up any leftover water and then unhook the flapper and replace it with a new one. Turn the water supply back on and test. If the toilet randomly runs or the tank starts filling by itself, it’s a sign that the flap is failing.

Why does my toilet randomly run for a few seconds?

Your toilet randomly runs on and off for a few seconds due to a problem called “phantom flush”. This is caused by a slow water leak from the tank into the bowl and is often the result of a sediment build-up on the flapper (aka “flush valve seal”) or a bad flapper seat.

Why is my toilet still running after replacing flapper?

The most likely cause is a leaking flush valve. Usually such a leak is around the mouth of the flush valve where the flapper is supposed to make a good seal. Lift the flapper and run your finger around the edge of the opening where water spills through the flush valve and into the bowl.

Why does my toilet keep filling up every few minutes?

If your toilet keeps refilling at 15-minute intervals, it probably has a leak. In the vast majority of cases, the problem is with the flapper, which is the rubber seal between the tank and the bowl. There’s a more serious possibility, however, and that is that the tank is leaking. If so, you’ll see water on the floor.

Where is the toilet flapper?

The toilet flapper is the component inside your toilet tank that lets water flow out of the tank and into the bowl when you flush. This round, rubber disc is attached to the bottom of the overflow tube, usually by mounting arms that hook onto ears on either side of the overflow tube.

How do you reset a toilet flapper?

Either one is usually easy to fix. Turn off the water valve and hold down the flush handle until the tank is empty. Adjust the chain holding the flapper to the flush handle. Clean the inlet holes in the toilet bowl if you can’t stop the flapper from sticking by adjusting the chain.

How long does a flapper last in a toilet?

The average toilet flapper lasts about 4 to 5 years. It is important that you replace your toilet flapper when needed to prevent damaging leaks.

Is a constantly running toilet an emergency?

A toilet that keeps running after its last use may seem like a minor annoyance (as long as it’s not flooding). However, the amount of water a malfunctioning toilet wastes will quickly add up. Even though a running toilet may not seem like an emergency, you need to get the problem fixed as soon as you can.

Will a running toilet increase water bill?

The most common cause for a high water bill is running water from your toilet. A continuously running toilet can waste up to 200 gallons a day. That can double a familyss typical water use, so fix toilet leaks as soon as possible.

Can a running toilet drain a well?

It is recommended that water well owners check at least yearly to make sure that their toilets are not running. A running toilet can run low producing wells dry. A silent toilet leak can waste from five to five hundred gallons of water per day! The ones you can hear will waste much, much more.

Why does my toilet cistern keep filling up?

If your cistern is constantly filling the most common problem is a faulty float valve or a poorly adjusted float arm. If your float valve is broken it means that the water level is not rising enough to shut off the water flow.

How do I know which toilet flapper?

Look at the flush valve drain opening at the bottom of your tank. If the opening looks about the size of a baseball or orange, you need a 2″ flapper. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.

How much does a toilet flapper cost?

Toilet Repair Price by Type of Replacement Part Replacement Cost (Labor Included) Fill Valve $60 – $120 Flapper $60 – $120 Shut-Off Valve $60 – $120 Seat $60 – $150.

Can you put Vaseline on a toilet flapper?

The flapper in the toilet opens and closes to let the water out of the tank. One easy, but temporary fix to make rubber toilet parts supple again is vaseline. The toilet must be drained and dried for this to work. Then, vaseline can be rubbed on the flapper and it’s connecting washer until they become soft.

What causes toilet flapper leak?

A dirty flapper can cause a leak due to algae or other minerals not allowing the flapper to properly close. If the flapper is dried out, warped, cracked, or pitted, then you’ll need to replace it. Check for cracks in the flush valve (the piece the toilet flapper seals against).

Are toilet flappers universal?

Are all toilet flappers universal? No. There are universal designs like the Fluidmaster flappers that replace most other flappers and there are specialty flappers for specific flushing systems.

Do toilet flapper valves wear out?

Replacing a Flapper Valve When you flush the toilet, the flapper lifts, letting water flow into the bowl. Although durable, the flapper can wear out over time, providing a less-than-perfect seal. The result is an audible trickle, punctuated by an occasional surge of supply water topping off the tank.

Do toilet flappers shrink?

Most flappers are either rubber or stiff plastic. When you flush your toilet, the flapper raises up and allows water to enter your toilet bowl. The flapper is essential a giant seal. It is not unusual for the flapper to eventually shrink, warp, or crack.