Table of Contents
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
How high should toilet flange be above tile floor?
Check the Flange Height The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal. If you recently tiled or changed the bathroom flooring, the flange height is likely less than optimal.
Can toilet flange be flush with tile?
The bottom of the flange must be flush with the tile, no gaps, or it could end up too high. You don’t want a large wax depth from having it too low and if it is too high, the toilet will rock. The seal is engineered to work best with the flange on top of the finished floor.
Should a toilet flange be flush with the finished floor?
When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits even or below the floor, then it’s wrong. These rings will prevent the toilet from properly recessing into the flange. Instead, use a standard ¾ inch wax ring.
What do you do if the toilet flange is above the floor?
To use grout to fix your flange: Start by mixing your grout. Get your toilet in place and set your toilet on four rubber shims. Take your mixed grout and pack it into the gap. Wait 24-hours before the grout to dry. Once dried, remove the shims.
Should you tile around or under a toilet?
The bathroom fitters are unanimous—if you’re looking for a high quality finish, with a better seal against water damage, then always tile the floor first. The floor will be sealed a lot better with the tiles being laid under the toilet. 2. It is also easier to do this rather than trying to cut tiles around the toilet.
What if toilet flange is not level?
If the toilet flange is not level, you should replace it. First, empty the toilet, remove the toilet tank and bowl, then remove the existing flange. Next, install the new flange and place a wax ring around it to keep it level.
What if my toilet flange is too low?
Low toilet flange is a common problem when installing a new (or in my case thicker mortar base). Unless your toilet is properly mated and sealed to the waste pipe, you may face problems related to sewer gas odor (it’s very unhealthy and unpleasant) and/or fluid leaks.
Can you put a toilet on top of a floating floor?
It’s considered best practice to always put a toilet on top of the flooring, whether the floor is made of wood, vinyl, tiles, etc. Not only will placing the toilet on top of the vinyl plank flooring generally look better, but it also ensures that the weight of the toilet is held by the floor and not the pipes.
When should you use an extra thick wax ring?
If your flange is floor level or slightly below then you can use an extra-thick wax ring. If the flange is lower than a 1/4” below the floor level then you should use a flange extension to raise the flange height or remove and replace the old floor flange and set it to the right height.
Does toilet flange go inside or outside pipe?
This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. Leave the old toilet flange right in place and glue on the new one at the right elevation for the floor, if it’s plastic. The flange should be sitting with the bottom edge flush with the top of the floor.
Can you shim a toilet flange?
How to Level a Toilet Using Toilet Shims. Toilet shims are thin plastic or rubber tabs that are used to level a toilet. You can also use homemade wooden shims or stainless steel coins. If a toilet is installed on an uneven floor or if the toilet flange is too high off the floor, the toilet will need to be shimmed.
Are there different size toilet flanges?
Toilet flanges come in six different types and three standard sizes with the option of an odd fit. The types are based on the material from which they are made, that is aluminum, copper, brass, stainless steel, plastic, and cast iron. The sizes also range from a four by three, four-inch, or three inches flange.
In what order should I remodel my bathroom?
How to renovate a bathroom: order of work > Assessing your requirements. > Setting a budget. > Choosing the perfect design. > Removing your old bathroom. > Installing your new bathroom. > Sanitary ware and fitted furniture. > Wall and floor coverings. > Lighting and ventilation.
Does toilet or floor install first?
Bathroom Construction Floor coverings such as vinyl then are placed on top of the subfloor. The toilet goes in next, and the vanity typically is installed last without a top, sink or faucets. If you’re doing a complete floor replacement, the vanity needs to be removed completely.
How long should you wait to use a newly installed toilet?
After installing the toilet, you have to wait at least 4-6 hours before it can be used © HouseHow.com. Many installers, out of pure laziness, do not silicone the base of the toilet after installing. A properly installed toilet should be caulked all around.
How long should toilet flange screws be?
Re: Screws? I use deck screws for setting those, usually 1″ or 1 1/2″ will do the lug 90 and 1 1/2″ or longer for the toilet flange. Re: Screws? For PVC flanges I use #14 screws 2″ long.
Should you glue a toilet flange?
pvc flange should be glued into a pvc pipe. IT would have been less of a problem if a plumber had made the replacement. Use a “good” flange and you will not have to do it again. Caulk is NOT glue.
