Table of Contents
Level the Toilet If it does not sit perfectly flat, it will rock and is more likely to leak over time. To correct this problem, slip toilet shims between the base and the floor to stop the rocking before bolting it down.
Should toilet be even with floor?
When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits even or below the floor, then it’s wrong. These rings will prevent the toilet from properly recessing into the flange. Instead, use a standard ¾ inch wax ring.
How tight should a toilet be to the floor?
You’re trying to avoid bowl movement, so that it doesn’t shift or fall over, not to hold the floor up by the toilet bolts. As tight as you can go will probably snap the porcelain (with a good socket you can torque a nut onto a bolt quite a bit). Until you think it’s about to snap is just guessing. Snug.
Should the toilet flange be flush with the floor?
5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.
Does a toilet need to be perfectly level?
2 Answers. There are purists out there that may say it must be level, but if it looks good setting there, I would let it set on the floor with no shims. It should not affect the operation of the flapper or valve that flushes the toilet.
How do I fill the gap between my toilet and floor?
Apply a thin, even bead of caulk around the base of the toilet to cover the gap along the floor and hide the shims. If necessary, smooth the caulk with your finger, wiping your finger clean frequently with a paper towel or a rag.
Should you tile under a toilet?
The bathroom fitters are unanimous—if you’re looking for a high quality finish, with a better seal against water damage, then always tile the floor first. The floor will be sealed a lot better with the tiles being laid under the toilet. 2. It is also easier to do this rather than trying to cut tiles around the toilet.
Why is my toilet loose from the floor?
Toilets wobble when they aren’t held securely to the floor, and if you let the wobble persist, they can leak and give you more serious problems. More often than not, the wobble is caused by loose toilet bolts, but the flange may also be responsible. It may be corroded, broken or set too high.
How are toilets attached to the floor?
How does the toilet attach to the floor? Toilets are attached to a metal or plastic collar known as a toilet floor flange. The flange itself is attached to the floor with screws. The flange leads to the soil stack, a large drain pipe designed to carry a large volume of liquid, etc.
Can you glue a toilet to the floor?
Remove the toilet and turn it on its side. Measure the depth and width of the gluing edge of the bowl. Next, move your caulk gun to the inset depth you just measured and apply caulk directly to the floor, maintaining the inset depth as you follow the tape. Install the wax ring and lower the toilet onto the flange.
Can toilet flange be lower than floor?
In a typical toilet installation, the floor flange that sits inside the drain opening below the toilet should be positioned so that its bottom surface rests flush against the finished floor or no more than 1/4 inch above or below the floor.
How do you install a toilet when the flange is too low?
Installation process is simple: install the gasket on top of the toilet flange on the floor, add spacer rings to match the new floor surface level, add the extender, add a standard wax ring the set the toilet on top. I like the product but I see some potential issues: Set-Rite spacer rings are hollow.
How thick is an extra thick wax ring?
If it’s at the same level, or no more than 1/4 inch below it, a regular wax ring, which is between 3/4 and 1 inch thick, is all you need. If the flange is recessed deeper than that, you need an extra-thick wax ring, which is about an inch thicker than a regular one.
What happens if toilet isnt level?
If the floor is not perfectly flat, the toilet will rock and the wax seal will be compromised. In this case the toilet must be shimmed to prevent it from rocking, but the shims can be installed in a manner that will allow the toilet to be level.
Where should I place my toilet level?
Place the carpenters level across the toilet bowl side to side and note where the bubble level is. Hammer a shim gently between the floor and the toilet base to bring a low side up. Continue to check the level in several directions around the toilet bowl and add more shims as necessary to level the bowl.
What do you put around bottom of toilet?
Caulking around the base of a toilet means an extra barrier to break through on top of the bolts and wax seal. On some floors, this may result in damage if removed improperly. It may also stain or leave smear marks if applied improperly, which can be difficult to remove without damaging the floor’s surface.
Are you supposed to put caulk around a toilet?
Caulk keeps the toilet secure Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It’s actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?Apr 4, 2019.
How often should a toilet seal be replaced?
The wax keeps water from leaking as it passes from the toilet to the drain pipe. It also seals against foul sewer gas odors. A wax seal will often last the life of the toilet, 20 or 30 years, without needing to be changed.
